【判断题】
在运用客车质量鉴定中,应急电源蓄电池电压低于40 V,属于C类故障
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【判断题】
大容量的熔断器熔断后,可用铜丝代替
A. 对
B. 错
【判断题】
列检更换大型配件时,工组长要亲自组织指挥和负责安全工作
A. 对
B. 错
【判断题】
在电气化铁路上,接触网的各导线及其相连部件,通常均带有高压电,因此禁止直接或间接地(通过任何物件,如棒条,导线,水流等)与上述设备接触
A. 对
B. 错
【判断题】
电气化区段车辆人员作业时在接触网未停电,未接地的情况下,禁止在各种车辆的车顶上进行任何作业
A. 对
B. 错
【判断题】
非电气化铁路区段的人员临时进入电气化铁路作业(包括通过电气化铁路的乘务员、各种检查人员等)时,必须接受电气化铁路安全教育
A. 对
B. 错
【判断题】
除供电段专业人员按规定作业外,任何人员及所携带的物件、使用的工具等,与接触网设备的带电部分必须保持2 m以上安全距离
A. 对
B. 错
【判断题】
在接触网未停电、接地的情况下可以用水冲刷车辆上部
A. 对
B. 错
【判断题】
处理故障的车辆距接触网不足2 m时,必须将车辆移至无接触网的线路上或按规定停电、接地后方准作业
A. 对
B. 错
【判断题】
动车组在段内或整备所进行整备作业后,司机必须亲自检查确认高压室内、地沟内和车下无作业人员,并与副司机呼唤应答、鸣笛后方可升弓
A. 对
B. 错
【判断题】
旅客列车运行途中,严禁关闭电子防滑装置、轴温报警装置和其他报警装置
A. 对
B. 错
【判断题】
在客车上安装宣传、引导标志及列车广告,须经铁路局主管部门批准,严禁在车内乱钉、乱贴、乱挂
A. 对
B. 错
【判断题】
空调客车的空调温控器应设定为:冬季14~16 ℃,夏季22~24 ℃
A. 对
B. 错
【判断题】
轴温达到110 ℃或超过外温加80 ℃时摘车处理
A. 对
B. 错
【判断题】
集中供电空调列车,库内停留期间须使用外接地面电源进行检修
A. 对
B. 错
【判断题】
全列空调列车供电制式不需一致
A. 对
B. 错
【判断题】
采用密接式车钩的列车,须备有中间体过渡车钩、15号过渡车钩、密接式车钩
A. 对
B. 错
【判断题】
列车编组中,密封风挡可以与橡胶风挡或铁风挡连挂
A. 对
B. 错
【判断题】
采用机车供电的旅客列车,因车辆故障造成机车跳闸或无法送电且不能修复时,必须甩车处理,尽快恢复全列车供电
A. 对
B. 错
【判断题】
旅客列车可以编挂制动关门车,但最后一辆不得为关门车
A. 对
B. 错
【判断题】
铁路是国家重要的基础设施,国民经济的大动脉,交通运输体系的骨干,是运输能力大、节约资源、有利环保的交通运输方式,在全面建设小康社会的进程中肩负着重要的历史使命
A. 对
B. 错
【判断题】
铁路使用的产品须符合国家和铁道行业技术标准,铁路重要产品须按照国家和铁道部有关规定,实行行政许可管理或产品强制认证
A. 对
B. 错
【判断题】
列车在电气化铁路发生火灾时,在不足4 m和未停电的情况下,可以使用水和一般的灭火器灭火
A. 对
B. 错
【判断题】
直达特快列车及动车组不设运转车长
A. 对
B. 错
【判断题】
列车在站内因其他乘务人员使用紧急制动阀临时停车,待停车原因消除且继续运行时,由运转车长(无运转车长为车辆乘务员)通知司机开车
A. 对
B. 错
【判断题】
行使运转车长职能的车辆乘务员可使用列车无线调度通信系统
A. 对
B. 错
【判断题】
特快旅客列车指列车运行图规定的速度超过120 km/h不超过160 km/h的旅客列车
A. 对
B. 错
【判断题】
列车发生火灾、爆炸时,须立即停车(停车地点应尽量避开特大桥梁、长大隧道等),并应立即通知供电部门停电
A. 对
B. 错
【判断题】
最高运行速度为160 km/ h的列车紧急制动距离限值为1 200 m
A. 对
B. 错
【判断题】
密接式车钩摘挂作业,车钩的摘挂和软管的摘结均由调车人员负责
A. 对
B. 错
【判断题】
密接式车钩的客车回送时,原则上应附挂旅客列车回送,附挂货物列车回送时,应挂于尾部,但不得超过2辆
A. 对
B. 错
【判断题】
旅客列车尾部加挂客车原则上不得超过2辆,遇特殊情况必须超过2辆时,应将运转车长值乘位置和列车尾部标志灯移至列车尾部
A. 对
B. 错
【判断题】
列车简略试验:有列检作业的由列检人员负责,无列检作业的由运转车长负责,无运转车长的由车辆乘务员负责,无车辆乘务员的由车站人员负责,挂有列尾装置的列车由司机负责
A. 对
B. 错
【判断题】
铁路信息技术一类设备应提供不低于5日×8 h技术支持与维护服务
A. 对
B. 错
【判断题】
列车调度电话、站间行车电话以及列车无线调度通信设备均须装设通信记录装置
A. 对
B. 错
【判断题】
车辆修程,客车和特种用途车按走行公里进行检修,最高运行速度不超过120 km/h的客车分为A1,A2,A3,A4
A. 对
B. 错
【判断题】
车辆须装有自动制动机
A. 对
B. 错
【判断题】
根据事故造成的人员伤亡、直接经济损失、列车脱轨辆数、中断铁路行车时间等情况,事故等级分为特别重大事故、重大事故、较大事故和一般事故
A. 对
B. 错
【判断题】
重大事故由国务院铁路主管部门组织事故调查组进行调查
A. 对
B. 错
【判断题】
事故调查报告是事故赔偿、事故处理以及事故责任追究的依据
A. 对
B. 错
【判断题】
一般事故分为:一般A类事故、一般B类事故、一般C类事故、一般D类事故
A. 对
B. 错
推荐试题
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续