【单选题】
磁粉探伤如果裂纹长度方向和磁力线平行,缺陷___.
A. 显示的最清楚
B. 显示不出来
C. 显示不明显
D. 显缺陷比较直观
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
电极触点法中,两个电极触点间距离正确的是___。
A. 40~80mm
B. 50~100mm
C. 60 ~150mm
D. 80~200mm
【单选题】
显象剂在工件表面上的厚度,正确的是___。
A. 0.05~0.07mm
B. 0.5~0.7mm
C. 0.5~1mm
D. 1~1.5mm
【单选题】
耐压试验目的不包括的检测项目是___。
A. 耐压
B. 泄漏
C. 疲劳
D. 破坏
【单选题】
基本除去焊条药皮吸附水的烘干温度正确的是___。
A. 50℃
B. 70℃
C. 80℃
D. 100℃以上 
【单选题】
偏心度过大的焊条,焊接时不产生___。 
A. 电弧偏吹
B. 焊接过程不稳定
C. 熔池保护不稳定
D. 烧穿
【单选题】
常用的显现粉,正确的是___。
A. 氧化镁
B. 氧化锌
C. 二氧化钛
D. 氧化钼
【单选题】
水压试验的压力表量程最好是试验压力的___倍。
A. 1倍
B. 2倍
C. 3倍
D. 4倍
【单选题】
气压试验时气体温度不得低于___。
A. 50℃
B. 10℃
C. 15℃
D. 20℃ 
【单选题】
密封性检验不能检查缺陷是___。
A. 漏水
B. 渗油
C. 内部气孔
D. 漏气 
【单选题】
CO2气体保护焊,当焊枪导电嘴间隙过大时,焊机可出现焊接___的故障。
A. 电流大
B. 电流小
C. 电流不变
D. 电流增加
【单选题】
手工钨极氩弧焊机检修时,___应对水质干净情况,是否漏水,是否畅通等检查。
A. 水路系统检修
B. 气路系统检修
C. 电路系统检修
D. 机械系统检修
【单选题】
电渣焊机的检修,要经常检查成形___滑块的磨损情况。
A. 冷却
B. 预热
C. 加热
D. 保温
【单选题】
采用___方法焊接焊件的焊接变形较小。
A. 氧~乙炔气焊
B. 等离子弧焊
C. 手工电弧焊
D. 氧~氢气焊 
【单选题】
电气原理图中的粗实线表示___。
A. 控制线路
B. 照明线路
C. 焊接电路
D. 以上三种都对
【单选题】
随着焊机负载持续率增加,焊机的许用电流___。
A. 减少
B. 增大
C. 不变
D. 很大
【单选题】
需要频繁启动电动机时,应选用___控制。
A. 刀开关
B. 负荷开关
C. 低压断路器
D. 接触器
【单选题】
对断路器灭弧室中SF6气体的微水含量的要求,应___。
A. 适当放宽
B. 具体情况具体对待
C. 从严控制
D. 根据开断容量确定
【单选题】
SF6气瓶存放时间超过___以上时,在使用前应进行抽检,以防止在放置期间可能引起的成分改变。
A. 3个月
B. 半年
C. 1年
D. 2年
【单选题】
互感器的二次绕组必须一端接地,其目的是___。
A. 提高测量精度
B. 确定测量范围
C. 防止二次过负荷
D. 保证人身安全
【单选题】
35kV电压互感器大修后,在20℃时的介质不应大于___。
A. 2%
B. 2.5%
C. 3%
D. 3.5%
【单选题】
定额内说明该项目另行计算者,应进行如下处理___。
A. 可换算入定额内
B. 建立补充定额
C. 由甲乙双方商定在独立费中处理
【单选题】
一般住宅层高3米。某住宅只一层,但高达9米,其建筑面积应按___层计算。
A. 1
B. 1.5
C. 3
D. 视不同情况而定
【单选题】
人工挖地槽、地坑定额深度为___米,超过时可另作补充定额。
A. 2
B. 3
C. 4
D. 5
E. 6
【单选题】
机械挖土方工程量,按机械挖土方___%。
A. 80
B. 20
C. 90
D. 10
【单选题】
砖基础施工所需工作面宽度为每边___mm。
A. 150
B. 200
C. 250
D. 300
【单选题】
人工挖土方,当挖土深度超过___米时,需增加工日。
A. 1.2
B. 1.5
C. 2
D. 以上答案都不对
【单选题】
双代号网络图由___个基本要素组成。
A. 2
B. 3
C. 4
D. 5
【单选题】
钻孔桩泥浆运输工程量按___计算。
A. 钻孔实体积以立方米
B. 产生的泥浆量以立方米C运输距离以米
【单选题】
建筑业能耗大,占全国能源量的___以上。
A. 1/3
B. 1/4
C. 1/5
D. 1/6
【单选题】
超过___m时叫深基础。
A. 4
B. 5
C. 2
D. 3
【单选题】
防水砂浆是在水泥砂浆中掺入水泥用量3%-5%的防水剂配制而成。铺设厚度为___mm。
A. 15-20
B. 20-25
C. 25-30
D. 30-50
【单选题】
土石坝施工料场规划实际可开采总量与坝体填筑量之比,—般为___。
A. 2-2.5
B. 1.5-2.0
C. 1.0-1.5
【单选题】
料场内装料面的间距以___m为宜。
A. 200
B. 150
C. 100
【单选题】
挖掘机开挖、自卸汽车运输两者配套时,自卸汽车运距为2.0km,车厢和铲斗容量的合理比值为___。
A. 3--5
B. 4--7
C. 7--10
【单选题】
心墙坝或斜墙坝施工,坝面应向上倾斜___的坡度。
A. 0.5%-1.5%
B. 1%-2%
C. 1.5%-2%
【单选题】
振动碾的压实影响深度可达___以上。
A. 0.5m
B. 0.8m
C. 1.0m
【单选题】
土石坝粘性土防渗体碾压部位的干容重、含水量取样次数为___。
A. 1次/(100~200)m3
B. 1次/(200~400)m3
C. 1次/(400~600)m3
【单选题】
钢立钻头的水口高度约为___。
A. 6-8厘米
B. 8-10厘米
C. 10-12厘米
D. 12-15厘米
【单选题】
钢衬接触灌浆质量检查方法为___。
A. 脚踢法
B. 锤击法
C. 手敲法
【单选题】
帷幕灌浆检查孔的压水试验,应在该部位灌浆结束后___进行。
A. 10天
B. 12天
C. 14天
D. 16天
推荐试题
【单选题】
vCenter Server Appliance Instance can be backed up using which Client Interface?___
A. vSphere Client Interface
B. vSphere Web Client Interface
C. VMware Host Client Interface
D. Virtual Appliance Management Interface
【单选题】
What tool can capture network traffic at the uplinks, or vSwitch, or virtual port levels?___
A. tcpdump-uw
B. wireshark
C. pktcap-uw
D. pcap
【单选题】
Which storage feature always requires the use of third-party software on ESXi?___
A. Hardware Acceleration for NAS devices
B. VVOL
C. Hardware Acceleration for Block
D. evices
【单选题】
An ESXi host's VMCA-Signed certificate has expired. How can the certificate be renewed?___
A. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Renew button.
B. In the vSphere Web Client, browse to the host in question. Click the Manage tab and select settings. Select System and click Certificate, then click the Refresh CA Certificates button.
C. Run the command /sbin/generate-certificates on the affected host.
D. Disconnect the host from vCenter Server and reconnect it.
【单选题】
Which is the correct order for upgrading vSphere components?___
A. vCenter Server, ESXi hosts, VMware Tools, Virtual Machine hardware
B. VMware Tools, Virtual Machine hardware, ESXi hosts, vCenter Server
C. vCenter Server, Virtual Machine hardware, VMware tools, ESXi hosts
D. ESXi hosts, vCenter Server, Virtual Machine hardware, VMware Tools
【单选题】
Which iSCSI initiator type can be used with any network interface card?___
A. Software iSCSI initiator
B. Software FCoE adapter
C. Hardware Independent iSCSI initiator
D. Hardware Dependent iSCSI initiator
【单选题】
An administrator is attempting to power on a virtual machine with 32GB of memory. The operation fails with the following error: <Could not power on VM: No space left on device> <Checking the space on the virtual machine's datastore, there is 30GB free.> Which action would allow the VM to power on?___
A. Set a 2GB memory reservation on the VM.
B. Mount the virtual disk from the affected VM on to another virtual machine and free up space from within the OS.
C. Enable vSphere HD admission control on the cluster in which the VM resides.
D. Set a 2GB memory limit on the VM.
【单选题】
An administrator attempts to manually reclaim space on thin-provisioned VMFS6 volumes but finds that no additional space is being recovered. Which could be causing this?___
A. vSphere 6.5 does not support manual UNMAP.
B. The manual UNMAP operation has been moved to the vSphere web client.
C. The VASA version is use is incompatible.
D. UNMAP is automated for VMFS6.
【单选题】
An administrator has upgraded to vSphere 6.5 and also wants to use Kerberos authentication for NFS. Which can be done to the existing NFSv3 volumes to enable this feature?___
A. Perform a storage rescan on VMFS volumes.
B. Unmount the NFSv3 datastore, and then mount as NFSv4.1 datastore.
C. Nothing. All NFSv3 mounted datastores are upgraded automatically during vSphere upgrades.
D. Perform a scan of new storage devices.
【单选题】
An administrator wants to restore the vCenter Server Appliance 6.5 from backup. Where can this be accomplished?___
A. from the ESXi Host Client
B. from the VMware vSphere Appliance Management Interface
C. from within the VMware vSphere Web Client
D. from the vCenter Server Appliance Installer
【单选题】
The administrator wants to power on VM-K2, which has a 2GHz CPU reservation. VM-M1, VM-M2, and VM-K1 are all powered on. VM-K2 is not powered on. The exhibit shows the parent and child resource reservations. If Resource Pool RP-KID is configured with an expandable reservation, which statement is true?___
A. VM-K2 will be unable to power on because there are insufficient resources.
B. VM-K2 will be able to power on since resource pool RP-KID has 2GHz available.
C. VM-K2 will be unable to power on because only 2GHz are reserved for RP-KID.
D. VM-K2 will receive resource priority and will be able to power on this scenario.
【单选题】
Which is the block size on the VMFS6 datastore?___
A. All small and large file blocks are 8MB.
B. All small and large file blocks are 1MB.
C. Small file blocks are 512KB. large file blocks are 64MB.
D. Small file blocks are 1MB, large file blocks are 512MB.
【单选题】
When installing vCenter Converter Standalone, why must an administrator perform a client-server installation instead of a local installation?___
A. to manage conversion tasks remotely
B. to convert virtual machines as well as physical machines
C. to allow installation of the Converter agent on remote source machines
D. to hot clone physical or virtual machines
【单选题】
Which is required by vCenter Converter Standalone to convert a physical Red Hat Enterprise Linux 7 machine to a virtual machine?___
A. The Linux machine must be powered off.
B. The Linux machine must have the SSH daemon started.
C. The Linux machine must use a static IP address.
D. The Linux machine must have a fully-qualified domain name.
【单选题】
An administrator is troubleshooting network communications between a vCenter Server and an ESXi 6.5 host. Which log shows the related events between these components?___
A. /var/log/fdm.log
B. /var/log/vpxa.log
C. /var/log/hostd.log
D. /var/log/auth.log
【单选题】
An administrator has recently upgraded from vSphere 6.0 to 6.5, and can no longer see the software iSCSI named vmhba33. Which could be the reason for this?___
A. The upgrade has changed the vmhba name.
B. vSphere 6.5 automates iSCSI configurations.
C. vSphere 6.5 no longer supports software iSCSI.
D. The upgrade has deleted the vmhba.
【单选题】
An administrator is trying to vMotion a VM from his datacenter to a recovery site. Which is the maximum allowed RTT (Round-Trip Time) latency between source and destination host?___
A. 100 milliseconds
B. 150 milliseconds
C. 15 milliseconds
D. 10 milliseconds
【单选题】
Which is required for configuring iSCSI Software Adapter network port binding?___
A. VMkernel of the iSCSI traffic must be load balanced using Route based on IP Hash algorithm.
B. VMkernel of the iSCSI traffic must be load balanced using Route based on Source Virtual Port ID algorithm.
C. VMkernel of the iSCSI traffic must be load balanced using Route based on Source MAC Hash algorithm.
D. VMkernel of the iSCSI traffic must be bound to only one active network adapter.
【单选题】
In vSphere Data Protection 6.1, which is the function of a Backup Verification job?___
A. None. Backup Verification job is not a feature of vSphere Data Protection
B. It is a manual task -Power it on -Verify the guest OS -Check started applications
C. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OS is booted by communicating with the Backup Verification agent
D. It is an automatic process -Restore a virtual machine -Power it on -Verify that the guest OC is booted by detecting the VMware ToolsTM "heartbeats"
【单选题】
An administrator has enabled vSphere Distributed Switch Health Check. The hosts connected to that Distributed Switch all display an alert:< vSphere Distributed Switch MTU supported status > .The administrator has all of the VMkernel ports MTU sizes set to 1600. Which action will remedy this problem?___
A. Configure the Distributed Switch to MTU 9100.
B. Disconnect and reconnect the physical network cable.
C. Configure the physical switch to MTU 1600.
D. Disable the Distributed Switch MTU.
【单选题】
Which Host Profile Subprofile configuration is used to configure firewall settings for ESXi hosts?___
A. Advanced Configuration Settings
B. General System Settings
C. Security
D. Networking
【单选题】
Where would a vSphere administrator find general vCenter Server logs on a vCenter Server Appliance?___
A. /var/log/vmware/vpxd/
B. /var/log/messages
C. /etc/vmware-vpx/
D. /var/log/vmware/vsan-health/
【单选题】
An administrator wishes to enable network port mirroring based on source port. Which feature should be enabled?___
A. vSphere standard switch port
B. ERSPAN
C. NSX Virtual Wire
D. VLAN
【单选题】
Which CLI command shows the physical uplink status for a vmnic?___
A. esxcli network ip connection list
B. esxcli network ip neighbor list
C. esxcli network nic get
D. esxcli network nic list
【单选题】
Which is the maximum number of block devices (LUNs) that are supported by ESXi hosts that are running version 6.5?___
A. 1024
B. 512
C. 2048
D. 256
【单选题】
When performing a vCenter Server 5.5 for Windows with Microsoft SQL Server Express database migration to vCenter Server Appliance 6.5, which will be the target database?___
A. Microsoft SQL Server Express 2012R2
B. Microsoft SQL Server Standard 2012R2
C. PostgreSQL
D. Oracle DB 11g
【单选题】
An administrator has multiple vCenter Server 6.5 systems but cannot enable Storage I/O Control (SIOC) on a datastore shared by ESXi hosts managed by the vCenter Server systems. Which action should the administrator take to resolve the issue?___
A. Unmount the datastore and then enable SIOC on the vCenter Server system.
B. Configure the datastore to be managed by a single vCenter Server system.
C. Configure Storage DRS and then enable SIOC on the vCenter Server system.
D. Enable Raw Device Mapping (RDM) on the
E. SXi hosts.
【单选题】
“OneAppServer” is a VM template stored in a content library named “LibraryOne”, but the vSphere administrator is not able to use this template for deployment. Why is the administrator unable to deploy OneAppServer?___
A. OneAppServer must be updated before it can be deployed.
B. LibraryOne is a subscribed library and OneAppServer is not downloaded yet.
C. LibraryOne is published and optimized for syncing over HTTP.
D. OneAppServer was imported from a local file on the system.
【单选题】
An administrator sets the Failover Capacity for both CPU and Memory at 25%. Based on the Exhibit below, how much of the cluster’s total CPU resources are still available to power on additional virtual machines?___
A. 45%
B. 25%
C. 70%
D. 60%
【单选题】
Which statement applies to the vSphere Replication appliance?___
A. Only one vSphere Replication appliance can be deployed per vCenter Server instance.
B. VMware Tools in the vSphere Replication appliance can be upgraded.
C. A single vSphere Replication appliance can manage a maximum of 4000 replications.
D. vSphere Replication is available only with the vSphere
E. ssentials Plus license.
【单选题】
Which esxcli namespace can a vSphere Administrator use to adjust the queue depth?___
A. esxcli system module parameters
B. esxcli storage core device
C. esxcli system module set
D. esxcli storage core adapter
【单选题】
Which statement regarding datastore clusters meets VMware’s recommended best practices?___
A. Clusters should contain only datastores presented from the same storage array.
B. Clusters should contain only datastores with equal hardware acceleration capability.
C. Clusters should contain only datastores with the same capacity.
D. Clusters should contain only datastores using the same connection method (iSCSI, FC, etc.).
【单选题】
What VM Monitoring setting would ensure that the maximum reset window for a virtual machine is 24 hours?___
A. Medium
B. Low
C. High
D. Normal
【单选题】
What is the default space threshold for vSphere Storage DRS?___
A. 80%
B. 70%
C. 90%
D. 95%
【单选题】
Which is the correct sequence to upgrade a vSphere infrastructure?___
A. vCenter Server>ESXi host> VMware Tools>VM compatibility
B. ESXi host>vCenter Server> VMware Tools>VM compatibility
C. vCenter host> ESXi host> VM compatibility> VMware Tools
D. ESXi host>vCenter Server> VM compatibility>VMware Tools
【单选题】
An administrator has a large boot from SAN cluster and wants to ensure consistent configuration by using host profiles. What special considerations are required for boot from SAN hosts?___
A. Change the “Device is shared clusterwide” setting to “false” in the host profile.
B. Verify that the boot LUN is correctly identified as the boot device in the host profile.
C. The boot from SAN device must report as a local device.
D. Host profiles are incompatible with boot from SAN hosts.
【单选题】
When using VMware Converter to import a Windows server and improve the consistency of the destination virtual machine, which optional step can be performed immediately prior to powering down the source server?___
A. Perform a final synchronization task.
B. Remove the server from the network.
C. Uninstall production applications.
D. Remove the server from the Active Directory domain.
【单选题】
Restoration of the vCenter Server Appliance is accomplished using which interface?___
A. vSphere Web Client
B. vSphere Client
C. vCenter Server Appliance Management Interface
D. vCenter Server Appliance GUI Installer
【单选题】
When attempting to migrate a virtual machine to another host in the same cluster, the error message, “Select a valid compute resource” returns. What could cause this error?___
A. Both hosts run different versions of ESXi.
B. Both hosts are not sharing the same datastore.
C. VMware Tools is not installed.
D. Virtual machine has an ISO attached.
【单选题】
When will vSphere Data Protection delete the expired backup image of a Platform Service Controller?___
A. Immediately after the retention period has expired.
B. After the expired backup image is restored.
C. During the next backup window following expiry.
D. During the next maintenance window following expiry.