【填空题】
57、制动隔离装置上的熄火控制开关应放置在___控制位,紧急自检时才会熄火;放在___位,紧急自检时不熄火。
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
熄火|直通
解析
暂无解析
相关试题
【填空题】
58、在键盘自检界面,针对每个按键,都有相应位置的按键显示,每按一个键,相应的按键会有颜色变化显示,以回应按键有效。如果需要退出键盘自检界面,按压___键,弹出“注意”窗口:“请确认退出键盘自检?”界面,把光标移动到“确定”按钮上,按压【确认】键,退出键盘自检,语音提示___。如图2-6所示。
【填空题】
59、键盘自检时应检测所有按键___,最后检测___键,完成键盘自检检测,否则没有检测的按键在数据记录分析中显示按键故障,键盘自检正常后,语音提示“自检正常”。
【填空题】
60、参数设定主要输入___等13项参数。
【填空题】
61、参数设置完成后,在主界面上会有___s当前设置的参数显示。
【填空题】
62、参数设置中,编组限速参数修改需___次确认;
【填空题】
63、参数设置时如果输入无效参数,则无法确认,语音提示“输入无效”,光标会自动跳转到___框予以提示。
【填空题】
64、司机号1、司机号2、车次:最多可以输入___位;使用调度命令发布的车次调用数据后,与实际运行方向相反时,建议规定车次使用方法。
【填空题】
65、根据运行区段、走行路径输入相应的交路___:“交路”栏输入数据交路号,“监控交路”栏输入___。交路上下行根据车次奇偶决定,偶数为上行,奇数为下行。
【填空题】
66、车站号:输入___车站对应交路的车站号,区间发车时输入___车站号,若地段特殊,输入前方车站号不能调用数据时,按___车站号输入。
【填空题】
67、公里标:即___公里标,建议按轨道车运行前方___信号机公里标或其它易于辨别的地面公里标进行输入。
【填空题】
68、若输入的对标公里标逻辑错误:不在___之间,语音提示输入无效,司机可以重新输入对标公里标。
【填空题】
69、若输入的公里标参数无法调取数据时,默认按输入车站号对应车站的___调取数据,若该车站号在本交路的上行、下行数据中均不存在,则无法调取数据,语音提示“输入无效”,DMI界面不显示车站信息;若则本行别数据交路中不存在,在相反行别的数据交路中存在,则语音提示“上行无此车站”或“下行无此车站”,DMI界面不显示车站信息。
【填空题】
70、公里标趋势:调用GYK基本数据时根据___自动设置,无需输入;未调用GYK基本数据时,根据运行方向增减趋势输入___。
【填空题】
71、编组限速:输入轨道车编组后允许的最高限速。管理参数中BTM设置为___时,编组限速设置范围为5-80km/h.管理参数中BTM设置___时,编组限速设置范围为5-120km/h;当对GYK编组限速进行修改并按压【确认】键退出参数设定界面后,DMI界面会弹出“再次确认参数”窗口,需要再次输入更改后的编组限速,如果两次输入的编组限速值不一致,会语音提示“输入无效”并文字提示两次编组限速不一致,需要重新进行输入。
【填空题】
72、总重:单位为吨。GYK出厂默认最大总重___。
【填空题】
73、辆数:连挂在一起的车辆总数。GYK出厂默认最大辆数___。
【填空题】
74、计长:整列车的长度除以11,可精确到小数点后一位。如输入2表示实际车长为22m。最大计长输入不超过___。
【填空题】
75、设定参数里的各个参数都不能超过它的范围,否则会语音提示“输入无效”,光标会自动跳转到错误参数框予以提示;参数输入时应注意观察设定窗口___的提示信息。
【填空题】
76、当GYK无___指令输出时,参数可在以下条件下修改:
【填空题】
___收到除___灯外的其他允许信号可以在实际速度___ km/h以下进行参数修改。
【填空题】
___收到___灯信号可以在实际速度___ km/h以下进行参数修改。
【填空题】
___收到___信号或按___信号控制的信号必须在停车后才能进行参数修改。
【填空题】
___区间作业模式运行中修改参数___。区间作业模式停车状态修改设定参数转为___模式。
【填空题】
不满足参数修改条件时,可以调出参数设置窗口,修改参数后,点击保存___。
【填空题】
77、揭示信息可通过U盘转储器输入,遇有无法及时编辑或传送运行揭示文件等特殊情况时,由司机___运行揭示信息。
【填空题】
78、当运行接近限速区段时,GYK右上角显示前方___km之内的有计划揭示与人工揭示,一次最多显示前方___km内的___条。
【填空题】
79、线路交汇点存在慢行限速时,若调度发布的慢行限速起点公里标不在运行线路中,司机应加强瞭望,避免进入限速地段时___。
【填空题】
①按压___键+提示信息___,可快速解除前方___km范围内的揭示,已起控的揭示不能解除。
【填空题】
②按压【查询】键,选择“3.计划揭示”将光标移到需要取消的揭示,按压___键,确认后即可解除。
【填空题】
③按压【查询】键,选择“3.计划揭示”直接按压数字键___,进入解除提示窗口。输入揭示类型、揭示序号、调度命令,将光标移到___选项上,按压【确认】键即可解除。
【填空题】
81、采用按压【确认】+序号的方式解除的揭示数据,重新调取数据后可___。
【填空题】
82、有计划揭示恢复:按压___键,选择“3.计划揭示”直接按压数字键___,进入恢复提示窗口。输入揭示类型、揭示序号、调度命令,将光标移到“确定”选项上按压【确认】键即可恢复。
【填空题】
83、揭示若被解除,则显示___色;揭示若过期,则显示___色。
【填空题】
84、若揭示下载失败,重新拔插U盘转储器,确认是否为U盘与DMI接口接触不良;如果DMI接口不良,可在___接口进行下载。如果揭示仍不能正常下载,司机必须按照管理规定进行处理。
【填空题】
85、有计划揭示下载后,将___上次下载的揭示文件;在揭示编辑时,应在揭示编辑软件中编辑当天有效的揭示文件,即删除过期的揭示文件,修改变动的揭示文件,添加新发布的揭示文件。
【填空题】
86、快速解除有计划限速的方法,只是解除当前状态下的限速控制,若参数重新设置后,快速解除的有计划限速会___。
【填空题】
87、在___窗口解除的有计划揭示,即使参数重新设置,解除的限速也不会起控。
【填空题】
88、若已下载的有计划揭示全部过期,则可通过揭示编辑软件生成一个揭示条数为___的揭示文件下载到DMI中,即可清除DMI中全部过期的有计划揭示,GYK按有计划揭示下载进行记录。
【填空题】
89、 人工揭示输入:按___键,进入“参数设定”窗口,将光标移到___项,按压【确认】键,进入临时限速设置界面如图4-4所示。
【填空题】
90、人工揭示输入时,当前线路的线路号在输入框___会有显示。如京沪线,线路号为2。
推荐试题
【单选题】
When troubleshooting VMware vCenter Server issues, when logging level provides maximum detail?___
A. Verbose
B. Trivia
C. Info
D. Error
【单选题】
What new feature is introduced in NFS 4.1 on ESXi 6.5?___
A. IPv6
B. KRB5i
C. AUTH_SYS
D. Storage DRS
【单选题】
What configuration option would ensure that a virtual NUMA topology is defined on VMs having more than eight virtual CPUs?___
A. cupid.coresPerSocket
B. numa.vcpu.followcorespersocket
C. numa.vcpu.maxPerVirtualNode
D. numa.vcpu.min
【单选题】
What is the minimum disk space required to deploy vSphere Data Protection (VDP) with 8 TB configuration?___
A. 4 TB
B. 16 TB
C. 8 TB
D. 12 TB
【单选题】
What advanced option for vSphere HA defines a maximum number of reset attempts by VMCP for a virtual machine?___
A. das.maxterminates
B. das.isolationshutdowntimeout
C. das.maxresets
D. fdm.isolationpolicydelaysec
【单选题】
What vSphere technology enables the administrator to ensure consistent configuration at scale?___
A. PowerCLI
B. Host Profiles
C. esxcli
D. vSphere Web Client
【单选题】
Which port is used for vSphere HA agent-to-agent communication?___
A. 443
B. 8182
C. 22
D. 902
【单选题】
Which log file would assist in identifying an issue that occurred during the database export phase of a vCenter Server upgrade process?___
A. vcdb_import.out
B. export.json
C. export-upgrade-runner.log
D. vcdb_export.out
【单选题】
Bidirectional CHAP is support by which storage initiator?___
A. software FCoE HBA
B. Fibre Channel HBA
C. independent hardware iSCSI HBA
D. dependent hardware iSCSI HBA
【单选题】
What is a pool of raw storage capacity that a storage system can provide to Virtual Volumes?___
A. protocol endpoint
B. storage container
C. storage provider
D. datastore
【单选题】
vSphere 6.5 DRS is now Network-Aware. Based on network utilization, when will DRS balance VMs?___
A. DRS will balance VMs when a network resource pool is configured for VMs.
B. DRS will balance VMs when Network I/O Control is enabled.
C. DRS will place VMs on initial boot for hosts that have network utilization lower that the threshold.
D. DRS will vMotion VMs when network utilization is higher than the threshold on a particular host.
【单选题】
A scripted upgrade of ESXi fails due to an incorrect parameter in the upgrade script. What file must the administrator modify to correct the problem?___
A. vmreconfig.pl
B. hostinfo.pl
C. ks.cfg
D. boot.cfg
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machine VM2. If a user is a member of group A and B, what action can the user perform?___
A. Suspend VM2.
B. Power off VM1.
C. Power on and power off VM1.
D. Power on and power off VM2.
【单选题】
The networking team has requested to have a dedicated network for iSCSI traffic. This task has been assigned to the vSphere Administrator. What is the VMware-recommended way to accomplish this?___
A. Configure Static Routes on each ESXi Server.
B. Configure the right subnet.
C. Create a custom IP Stack.
D. Define a dedicated gateway for the iSCSI vmkernel.
【单选题】
To prevent possible failures or issues during a vSphere upgrade, which component should be upgraded first?___
A. ESXi Hosts
B. virtual machines
C. datastores
D. vCenter Server
【单选题】
What is the command for updating an ESXi host?___
A. esxcli software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
B. esxupdate software update –d”/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
C. esxcli software update –d “/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
D. esxupdate software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
【单选题】
A vSphere Administrator would like to identify which physical NUMA node their virtual machine is currently residing on. What esxtop metric would provide this information?___
A. GST_ND[x]
B. OVD_ND[x]
C. NRMEM
D. NHN
【单选题】
How can a vSphere administrator ensure that two virtual machines never run on the same datastore in a datastore cluster, while permitting the VMs to be load-balanced?___
A. Use an Intra-VM Anti-Affinity Rule.
B. Configure a storage DRS VM override.
C. Disable storage
D. RS for the VMs.
【单选题】
What is the VMware-recommended way to move a physical adapter out of Network I/O Control’s scope?___
A. Set the teaming policy to “Route Based on Physical NIC Load.”
B. Add the vmnic to the Net.NetNiocAllowOverCommit parameter in Advanced System Settings.
C. Add the vmnic to the Net.IOControlPnicOptOut parameter in Advanced System Settings.
D. Move the vmnic to a different vmUplink port on the Distributed Switch.
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machines, defined on the VM folder and its children. If a user is a member of Groups A and B, what will be the user’s effective permission on VM1 and VM2?___
A. Power on
B. Power off.
C. Power on and Power off.
D. Reset.
【单选题】
Group 1 is granted console interaction on a VM folder. User 1 is granted no console interaction on the same VM folder. What will be the outcome if User 1 tries to access the console of a virtual machine?___
A. User 1 will not be able to access the virtual machines in the VM folder.
B. User 1 will not have access to the virtual machine console.
C. User 1 will have access to the virtual machine console.
D. User 1 will have console access only via the vSphere Web Client.
【单选题】
Which statement is true regarding the use of VMFS3 datastores with vSphere 6.5?___
A. VMFS3 datastores can be used but not created.
B. VMFS3 datastores can be neither used nor created.
C. VMFS3 datastores will be present but unmounted.
D. VMFS3 datastores can be created and used.
【单选题】
In the Exhibit, each VM has a 1GHz non-expandable reservation. If all VMs are powered on in sequence, what would be the outcome?___
A. VM4 cannot be powered on.
B. VM5 cannot be powered on.
C. VM6 cannot be powered on.
D. VM3 cannot be powered on.
【单选题】
vSphere 6.5 introduced MAClearning capabilities for VMware’s virtual switches. What three benefits will it provide? (Choose three.)___
A. Reduced memory consumption.
B. Reduced consumption of extra CPU cycles.
C. Increased network throughput.
D. Prevent packet flooding inside the vSwitch.
【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia