【单选题】
DCJ(FCJ)励磁吸起后，在_______复原。[322020201]___
A. 始端JXJ励磁后
B. 道岔转换后
C. 终端JXJ励磁后
D. SJ落下时
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
D
解析
暂无解析
相关试题
【单选题】
6502电气集中进路选择继电器JXJ吸起后，在_______时复原。[322020201]___
A. 终端AJ落下
B. KF-共用-Q断电
C. DCJ或FCJ落下
D. 始端AJ落下
【单选题】
ZP.Y2-18型移频自动闭塞轨道电路在晴天做分路试验，用0.06Ω电阻线分路时，在接收盘的“接入”孔上测试，一般电压为几十毫伏，最大不应超过_______。[321010101]___
A. 90mV
B. 100mV
C. 110mV
D. 120mV
【单选题】
差置调车信号机ZJ的电路中1LJ和2LJ接点的作用是_______。[321020201]___
A. 实现进路锁闭
B. 防止调车尾追列车
C. 检查敌对进路未建立
D. 防止同时向无岔区段调车
【单选题】
当出站信号机有两个发车方向且向主要线路发车时，_______吸起。[321020201]___
A. ZXJ(主信号继电器)
B. XFJ(信号辅助继电器)
C. LXJ和ZXJ
D. ZXJ、XFJ、LXJ
【单选题】
6502电气集中，调车进路辅助开始继电器FKJ和终端继电器ZJ的励磁顺序是_______。[323020201]___
A. FKJ先吸起
B. ZJ先吸起
C. 进路左边的先吸起
D. 进路右边的先吸起
【单选题】
6502大站电气集中，进路在接近锁闭状态，应能办理人工解锁，待信号关闭后，接车进路和正线发车进路延时_______解锁。[323010201]___
A. 10s
B. 30s
C. 1min
D. 3min
【单选题】
在进路遇有超限绝缘时，应把检查条件加在_______。[323030101]___
A. QJJ电路，由9线检查
B. XJ电路，由11线检查
C. XJJ电路，由8线检查
D. XJ电路，由7线检查
【单选题】
排进路过程中，道岔转换时，如有车辆驶入道岔区段，因道岔控制电路_______的极性接点能保持不动，所以道岔能继续转换到底。[323020201]___
A. 1DQJ
B. 1DQJ保持吸起和2DQJ
C. 2DQJ
D. 1DCJ和2DCJ
【单选题】
场间联络线两端设接车进路信号机时，必须使股道上的发车进路信号机所防护的进路长度等于或大于_______，否则不准设置接车进路信号机。[321030202]___
A. 400m
B. 800m
C. 1000m
D. 1200m
【单选题】
在SJ电路中，FDGJ接点的作用是_______。[323020201]___
A. 防止闪白光带
B. 防止轻型车跳动时错误解锁
C. 检查QJJ电路完整
D. 实现区段锁闭
【单选题】
在有两个发车口的车站往主要发车口发车时，为了防止出站信号机开放一个绿灯前有先闪一下两个绿灯的现象，电路中采用的安全措施是_______。[333020201]___
A. LXJ先于ZXJ吸起
B. LXJ先于XFJ吸起
C. ZXJ先于XFJ吸起
D. ZXJ先于LXJ吸起
【单选题】
6502电气集中在排列进路过程中，进路始端按钮表示灯在_______熄灭。[322020201]___
A. 进路锁闭后
B. XJ吸起后
C. 方向电源无电后
D. 选路完毕后
【单选题】
6502电气集中调车XJJ在_______时，XJJ1-2线圈自闭电路接在8网络线上。[322020201]___
A. JYJ落下、QJ吸起
B. JYJ吸起
C. XJ吸起
D. QJ落下
【单选题】
6502电气集中在12线上串接QJJ第二组接点其作用是_______。[322020201]___
A. 防止提前解锁
B. 防止道岔中途转换
C. 防止迂回电流
D. 保证供电
【单选题】
办理人工解锁时，QJ的落下时机是_______。[321020201]___
A. KF-ZQJ-Q无电→QJ↓
B. 1RJJ↑→QJ↓
C. XJJ↓→QJ↓
D. KZ-RJ-H无电→QJ↓
【单选题】
6502电气集中KJ复原的时机是_______。[322020201]___
A. 进路内第一个道岔区段解锁后
B. 进路锁闭后
C. 信号开放后
D. 进路内所有的区段解锁后
【单选题】
接车方向的并置调车信号机作阻拦信号，此时ZJ吸起所检查的条件电源是_______。[32202021]___
A. KF-DFJ-Q
B. KF-DJJ-Q
C. KF-列共-DJJ-Q
D. KF-共用-Q
【单选题】
按压接车方向调车信号机按钮后可供下列电源中的_______。[321020201]___
A. KZ-列共-Q
B. KZ-共用-Q
C. KF-DJJ-Q
D. KF-DFJ-Q
【单选题】
5/72DCJ自动复原的条件是_______。[321020201]___
A. 5/71SJ落下
B. 5/72SJ落下
C. KZ-ZQJ-H有电
D. KF-共用-Q有电
【单选题】
办理D3往IG的长调车进路时，有关的FKJ、KJ动作顺序应是_______。[321020201]___
A. FKJ自左向右，KJ自右向左顺序吸起
B. FKJ、KJ均为自左向右顺序吸起
C. FKJ、KJ均为自右向左顺序吸起
D. FKJ自右向左，KJ自左向右顺序吸起
【单选题】
在选双动道岔反位时，1DQJ的励磁条件是通过_______的接点接入KF。[322020201]___
A. 1FCJ62
B. 1DCJ63
C. 2FCJ62
D. 2DCJ63
【单选题】
在分线盘上X1(或X2)与X3线端子测电压判断道岔表示故障，当交流2V左右、直流为0V时，可判断为_______。[333020201]___
A. 室外二极管击穿短路
B. 室外断线
C. 室内断线
D. 电容短路
【单选题】
接车方向单置调车信号机按钮作为发车方向调车进路变通按钮时，其AJ用_______作为励磁条件之一。[332000000]___
A. KF-共用-Q
B. KF-DFJ-Q
C. KZ-列共-DJJ-Q
D. KZ-列共-DFJ-Q
【单选题】
6502电气集中四线制道岔定位无表示，定位表示继电器颤动，说明_______。[333020201]___
A. 室外开路
B. 室内表示电路电容故障
C. 室内继电器开路
D. 室外二极管开路
【单选题】
6502电气集中DXJ复原的时机是_______。[322020201]___
A. 进路内第一个道岔区段解锁后
B. 进路锁闭后
C. 信号开放后
D. 进路内所有的区段解锁后
【单选题】
发车方向单置调车信号机按钮作为接车方向调车进路变通按钮时，其AJ用_______为励磁条件之一。[332010201]___
A. KF-共用-Q
B. KF-DFJ-Q
C. KZ-列共-LFJ-Q
D. KZ-列共-DJJ-Q
推荐试题
【单选题】
A scripted upgrade of ESXi fails due to an incorrect parameter in the upgrade script. What file must the administrator modify to correct the problem?___
A. vmreconfig.pl
B. hostinfo.pl
C. ks.cfg
D. boot.cfg
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machine VM2. If a user is a member of group A and B, what action can the user perform?___
A. Suspend VM2.
B. Power off VM1.
C. Power on and power off VM1.
D. Power on and power off VM2.
【单选题】
The networking team has requested to have a dedicated network for iSCSI traffic. This task has been assigned to the vSphere Administrator. What is the VMware-recommended way to accomplish this?___
A. Configure Static Routes on each ESXi Server.
B. Configure the right subnet.
C. Create a custom IP Stack.
D. Define a dedicated gateway for the iSCSI vmkernel.
【单选题】
To prevent possible failures or issues during a vSphere upgrade, which component should be upgraded first?___
A. ESXi Hosts
B. virtual machines
C. datastores
D. vCenter Server
【单选题】
What is the command for updating an ESXi host?___
A. esxcli software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
B. esxupdate software update –d”/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
C. esxcli software update –d “/vmfs/volumes/Datastore/DirectoryName/PatchName.zip”
D. esxupdate software vib update –d /vmfs/volumes/Datastore/DirectoryName/PatchName.zip
【单选题】
A vSphere Administrator would like to identify which physical NUMA node their virtual machine is currently residing on. What esxtop metric would provide this information?___
A. GST_ND[x]
B. OVD_ND[x]
C. NRMEM
D. NHN
【单选题】
How can a vSphere administrator ensure that two virtual machines never run on the same datastore in a datastore cluster, while permitting the VMs to be load-balanced?___
A. Use an Intra-VM Anti-Affinity Rule.
B. Configure a storage DRS VM override.
C. Disable storage
D. RS for the VMs.
【单选题】
What is the VMware-recommended way to move a physical adapter out of Network I/O Control’s scope?___
A. Set the teaming policy to “Route Based on Physical NIC Load.”
B. Add the vmnic to the Net.NetNiocAllowOverCommit parameter in Advanced System Settings.
C. Add the vmnic to the Net.IOControlPnicOptOut parameter in Advanced System Settings.
D. Move the vmnic to a different vmUplink port on the Distributed Switch.
【单选题】
A VM folder contains VM1 and VM2. Group A has permission to power on virtual machines, defined on the VM folder and its children. Group B has permission to power off virtual machines, defined on the VM folder and its children. If a user is a member of Groups A and B, what will be the user’s effective permission on VM1 and VM2?___
A. Power on
B. Power off.
C. Power on and Power off.
D. Reset.
【单选题】
Group 1 is granted console interaction on a VM folder. User 1 is granted no console interaction on the same VM folder. What will be the outcome if User 1 tries to access the console of a virtual machine?___
A. User 1 will not be able to access the virtual machines in the VM folder.
B. User 1 will not have access to the virtual machine console.
C. User 1 will have access to the virtual machine console.
D. User 1 will have console access only via the vSphere Web Client.
【单选题】
Which statement is true regarding the use of VMFS3 datastores with vSphere 6.5?___
A. VMFS3 datastores can be used but not created.
B. VMFS3 datastores can be neither used nor created.
C. VMFS3 datastores will be present but unmounted.
D. VMFS3 datastores can be created and used.
【单选题】
In the Exhibit, each VM has a 1GHz non-expandable reservation. If all VMs are powered on in sequence, what would be the outcome?___
A. VM4 cannot be powered on.
B. VM5 cannot be powered on.
C. VM6 cannot be powered on.
D. VM3 cannot be powered on.
【单选题】
vSphere 6.5 introduced MAClearning capabilities for VMware’s virtual switches. What three benefits will it provide? (Choose three.)___
A. Reduced memory consumption.
B. Reduced consumption of extra CPU cycles.
C. Increased network throughput.
D. Prevent packet flooding inside the vSwitch.
【单选题】
What is the default pathing policy for most active-active arrays?___
A. Fixed
B. Most Recently Used
C. Dynamic
D. isk Morroring
【单选题】
Which command will show the iSCSI sessions on a ESXi 6.5 host?___
A. esxcli storage iscsi session get
B. esxcli iscsi session get
C. esxcli storage iscsi session
D. esxcli iscsi session list
【单选题】
Which of the following is not a parameter for traffic filtering or marking?___
A. virtual port ID
B. Protocol
C. Traffic Direction
D. DSCP value
E. Traffic redirection
【单选题】
A vSphere administrator wants to enable a virtual machine with Secure Boot, but in VM setting, Secure Boot option was not found under Boot Options. What could be the cause?___
A. The virtual hardware is not compatible.
B. The virtual machine has missing drivers.
C. The virtual machine OS does not support secure boot.
D. VMware Tools is not upgraded.
【单选题】
A virtual machine is connected on a distributed port group where the average bandwidth configured in the traffic shaping policy is 100 Mbps. The VM network adapter is configured with a reservation of 200 Mbps. What is the VM’s effective bandwidth?___
A. 200 Mbps
B. 100 Mbps
C. 150 Mbps
D. 400 Mbps
【多选题】
What are two reasons why a datastore in a Storage DRS cluster cannot enter maintenance mode?(Choose two.)___
A. Storage latency is too high to allow Storage DRS initiate Storage vMotion.
B. Storage DRS is configured for a VMFS3 datastore.
C. Storage
D. RS is disabled on the virtual disk.
【多选题】
What two methods are used to configure VMware vSphere Storage I/O Control shares and limits? (Choose two.)___
A. Assign shares and limits to VM virtual disks.
B. Assign shares and limits to datastores.
C. Assign shares and limits to Storage (DRS) clusters.
D. Assign shares and limits using VM storage policies.
【多选题】
ESXi 6.5 introduces VMFS6, which supports both 512e and 512n devices. What three configurations are supported when using these devices? (Choose three.) ___
A. Hosts with both 512e and 512n devices.
B. Storage vMotion between both 512e and 512n devices.
C. Datastore Extents spanned between both 512e and 512n devices.
D. Storage DRS clusters containing only both 512e and 512n devices.
【多选题】
A vSphere Administrator observes that the Primary VM configured with Fault Tolerance is executing slowly. After further investigation, it is determined that the Secondary VM is on an overcommitted ESXi host. What two methods will correct the problem? (Choose two.)___
A. Use Storage vMotion to migrate the Secondary VM to another datastore.
B. Use vMotion to migrate the Secondary VM to a different ESXi host.
C. Configure a CPU limit on the Primary VM which will also apply to the Secondary VM.
D. Turn off and turn on FT in order to recreate the Secondary VM on a different datastore.
【多选题】
Which two features require the use of Host Profiles? (Choose two.)___
A. Host Customizations
B. shared storage
C. Auto
D. eploy
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
What three processes on the vCenter Server Appliance (VCSA) does“vmware-watchdog monitor? (Choose three.) ___
A. vmware-eam
B. vmcad
C. vmware-vpostgres
D. vpxd
E. vsan-health
【多选题】
Which two statements correctly describe VM-Host affinity rules? (Choose two.) ___
A. When there is more than one VM-Host affinity rule in a vSphere DRS cluster, the rules are applied equally.
B. After creating a VM-Host affinity rule, its ability to function in relation to other rules is predetermined.
C. When there is more than one VM-Host affinity rule in a vSphere
D. RS cluster, the rules will be ranked.
【多选题】
An administrator wants to enable proactive HA by moving virtual machines automatically if a hardware alert is triggered. What are the three required settings? (Choose three.)___
A. Set vSphere DRS Automation to Partially Automated.
B. Turn on Proactive HA.
C. Set the Proactive HA Automation Level to Manual.
D. Set the Proactive HA Automation Level to Automated.
E. Turn on vSphere HA and vSphere DRS.
【多选题】
If vCenter Server 5.5 installation has one or more services deployed remotely, which three services are relocated to vCenter Server 6.5 on upgrade? (Choose three.)___
A. vCenter Inventory Services
B. vSphere Authentication Proxy
C. vSphere Web Client
D. vSphere
E. SXi Dump Collector
【多选题】
What two debugging levels can a virtual machine be configured to? (Choose two.)___
A. Verbose
B. Debugging
C. Statistics
D. Trivia
【多选题】
What are three benefits of using a few large-capacity LUNs instead of many small-capacity LUNs? (Choose three.) ___
A. Better performance because there is less contention for a single volume.
B. More flexibility for resizing virtual disks.
C. Less wasted storage space.
D. More flexibility to create virtual machines without adding new LUNs.
E. Fewer VMFS datastores to manage.
【多选题】
Which two configurable options are available in Boot Options for a virtual machine? (Choose two.)___
A. Tools Upgrades
B. Encryption
C. Firmware
D. Force BIOS setup
【多选题】
Which three VMware-recommended best practices should an administrator follow before upgrading to vSphere 6.5? (Choose three.)___
A. Disconnect ESXi host from vCenter.
B. VMware Tools are installed in the virtual machine.
C. Ensure that the system hardware complies with ESXi requirements.
D. Back up the host.
E. Check the interoperability of any other software integrated with vSphere.
【多选题】
What are two requirements to enable EVC in vSphere DRS cluster? (Choose two.)___
A. CPUs must be from the same vendor.
B. EVC must use the lowest possible baseline supported by the hardware.
C. CPUs must be in the same family and of the same speed.
D. No VMs may be running in the cluster.
【多选题】
What three conditions could result in VMware Flash Read Cache being unable to claim a disk? (Choose three.)___
A. The disk is not listed in the VMware hardware compatibility guide.
B. The disk is not detected as an SSD.
C. The disk is not detected as local.
D. The disk is in use by VMFs.
【多选题】
Boot from SAN is supported on which three storage technologies? (Choose three.)___
A. VMware vSAN
B. FCoE
C. NFS 4.1
D. iSCSI
E. FC
【多选题】
Which two components are part of storage I/O multipathing on ESXi? (Choose two.)___
A. SATP
B. VASA
C. PSP
D. VAAI
【多选题】
Which two statements are true about Highly Available vSphere Auto Deploy infrastructure? (Choose two.)___
A. It helps prevent data loss.
B. It is a prerequisite for using vSphere Auto Deploy with stateful install.
C. It requires two or more Auto
D. eploy servers.
【多选题】
The virtual machine log rotation size can be changed for all VMs by which two interfaces? (Choose two.)___
A. PowerCLI
B. vSphere Web Client
C. ESXi host client
D. esxcli
【多选题】
Which two configuration options can exclude virtual disks from snapshot operations? (Choose two.)___
A. Use RDM in virtual mode for virtual disk.
B. Use virtual disks in Independent – Persistent mode.
C. Use a virtual disk larger than 2 TB in size.
D. Use RDM in physical mode for virtual disk.
【多选题】
Which two storage configurations on the source server are unsupported with VMware Converter? (Choose two.)___
A. Linux LVM
B. software RAID
C. GPT/MBR hybrid disks
D. Windows basic volumes
E. Windows dynamic volumes
