【判断题】
空气呼吸器压力越高,使用时间越长
A. 对
B. 错
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【判断题】
爆炸是物质在瞬间以机械功的形式释放出大量气体、液体和能量的现象。其主要特征是压力的急剧下降
A. 对
B. 错
【判断题】
限制火灾爆炸事故蔓延的措施是分区隔离,配置消防器材和设置安全阻火装置
A. 对
B. 错
【判断题】
压缩机开车前需要进行暖管、保证蒸汽进入透平机时不带凝酒、避免叶片损坏
A. 对
B. 错
【判断题】
大火封门无法逃生时.可用浸湿的毛巾衣物堵塞门缝.发出求救信号等待救援
A. 对
B. 错
【判断题】
二氧化硫能和一些有色物质结合生成不稳定的无色物质,可用于漂白一些有机物质
A. 对
B. 错
【判断题】
乙烯精偃塔发生冻塔,塔的压差较高'塔顶塔釜产品不合格,需要及时注解冻剂解冻
A. 对
B. 错
【判断题】
乙烯压缩机油路系统开车时、必须先投用隔离气系统。否则润滑油会漏进干气密封,损坏密
A. 对
B. 错
【判断题】
人身中毒的途径为呼吸道、消化道、皮肤
A. 对
B. 错
【判断题】
水力清焦只许在环境温度0℃以上进行
A. 对
B. 错
【判断题】
有氢气存在的设备容易发生氢腐蚀
A. 对
B. 错
【判断题】
鉴定为危险废物的废催化剂、废吸附剂等委托有资质的单位进行无害化处置
A. 对
B. 错
【判断题】
发生硫化氢急性中毒时、
A. 对
B. 错
【判断题】
在短时间内吸入大量苯蒸汽可引起急性中毒、严重时可因呼吸衰羯而死亡
A. 对
B. 错
【判断题】
乙烯装置在开停车过程中燈类排放量较大、因此多采用高架火炬
A. 对
B. 错
【判断题】
降低燃料中硫含量,能有效降低烟气中二氧化硫排放
A. 对
B. 错
【判断题】
芳动者短时间活动的有毒气体工作场所、宜设置固定式有毒气体检测报警仪
A. 对
B. 错
【判断题】
装置负荷低时.锅炉给水用量少、锅炉给水泵出口压力高、裂解炉汽包'液面调节阀的前后压差也高、容易使锅 炉给水调节阀冲刷损坏
A. 对
B. 错
【判断题】
裂解炉汽包连续排污的目的是在事故状态时保证'液位
A. 对
B. 错
【判断题】
34、乙烯裂解炉在清焦与开车过程中可引起温差及热变应力腐蚀
A. 对
B. 错
【判断题】
335;裂解炉联锁停炉后.在安全的前提下,最先应关注稀释蒸汽是否适量即时通入.保护炉管不能超温
A. 对
B. 错
【判断题】
危险废物是指列入国家危险废物名录或是根据国家规定的危险废物鉴别标准和鉴别方法认定具有危险特性的废物
A. 对
B. 错
【判断题】
利用安全检查表
A. 对
B. 错
【判断题】
电器着火可以用泡沫灭火器灭火
A. 对
B. 错
【判断题】
裂解炉冬季停用时.炉内保持一定数量的火嘴处于燃烧状态是为了防止炉管低温腐蚀
A. 对
B. 错
【判断题】
为了避免出现炉管破裂事故.裂解炉进行蒸汽吹灰前必须先进行排凝
A. 对
B. 错
【判断题】
裂解炉运行过程中加入二甲基二硫的主要原因为抑制一氧化碳生成防止甲烷化飞温
A. 对
B. 错
【判断题】
燃烧是一种同时伴有发光、发热的激烈的氧化反应.具有发光、发热和生成新物质三个特征
A. 对
B. 错
【判断题】
负有危险化学品安全监督管理职责的部门的工作人员.在危险化学品安全监督管理工作中滥用职权、玩忽 职守、徇私舞弊.构成犯罪的.依法追究刑事责任、尚不构成犯罪的依法给予处分
A. 对
B. 错
【判断题】
碳在空气中燃烧.生成二氧化碳
A. 对
B. 错
【判断题】
345乙烯精馏塔取样分析乙烯产品时、不需要防止冻伤
A. 对
B. 错
【判断题】
346控制室或化验室的室内不得安装可燃气体、液化烃和可燃液体的在线分析仪器
A. 对
B. 错
【判断题】
裂解炉烟气中控制氮氧化物排放量是为了保护环境
A. 对
B. 错
【判断题】
防治污染的设施不得擅自拆除或者闲置.确有必要拆除或者闲置的.必须征得所在地环境保护行政主管部门同意
A. 对
B. 错
【判断题】
消防安全管理人应当定期向消防安全责任人报告消防安全情況及时报告涉及消防安全的重大问题
A. 对
B. 错
【判断题】
应急预案的编制应当符合有关法律、法规、规章和标准的规定、结合本地区、本部门、本单位的安全生产 实际情况
A. 对
B. 错
【判断题】
离心泵在停泵之前要先关小出口阀门.以免出口管线的物料倒流入泵内使叶轮受到冲击而损坏
A. 对
B. 错
【判断题】
生产使用的机械设备必须建立健全安装、使用、检查、维修、保养制度、不准超温、超压、超负荷运行.在 一般情况下可以超期服役
A. 对
B. 错
【判断题】
安全色是表达安全信息含义的颜色.应用安全色可使人们
A. 对
B. 错
【判断题】
在职业危害识别过程中.生产中使用的全部化学品、中间产物和产品均需要进行职业卫生检测
A. 对
B. 错
【判断题】
汽化时与液体接触较与蒸汽接触的部位更易腐蚀
A. 对
B. 错
推荐试题
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于
【单选题】
12.对于电阻性负载,熔断器熔体的额定电流___线路的工作电流。
A. 远大于
B. 不等于
C. 等于或略大于
D. 等于或略小于
【单选题】
13.对于电动机负载,熔断器熔体的额定电流应选电动机额定电流的___倍。
A. 1~1.5
B. 1.5-2.5
C. 2.0~3.0
D. 2.5~3.5
【单选题】
14.使用快速熔断器时,一般按___来选择。
A. IN=1.03IF
B. IN=1.57IF
C. IN=2.57IF
D. IN=3IF
【单选题】
15.断路器中过电流脱扣器的额定电流应该大于等于线路的___。
A. 最大允许电流
B. 最大过载电流
C. 最大负载电流
D. 最大短路电流
【单选题】
16.短路电流很大的电气线路中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
17.一般电气控制系统中宜选用___断路器。
A. 塑壳式
B. 限流型
C. 框架式
D. 直流快速
【单选题】
18.交流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
19.直流接触器一般用于控制___的负载。
A. 弱电
B. 无线电
C. 直流电
D. 交流电
【单选题】
20.接触器的额定电压应不小于主电路的___。
A. 短路电压
B. 工作电压
C. 最大电压
D. 峰值电压
【单选题】
21.接触器的额定电流应不小于被控电路的___。
A. 额定电流
B. 负载电流
C. 最大电流
D. 峰值电流
【单选题】
22.对于___工作制的异步电动机,热继电器不能实现可靠的过载保护。
A. 轻载
B. 半载
C. 重复短时
D. 连续