【单选题】
在气相色谱分析中，一个特定分离的成败，在很大程度上取决于___的选择。
A. 检测器
B. 色谱柱
C. 皂膜流量计
D. 记录仪
查看试卷，进入试卷练习
微信扫一扫，开始刷题
答案
B
解析
暂无解析
相关试题
【单选题】
气相色谱分析的仪器中，载气的作用是___。
A. 载气的作用是携带样品，流经汽化室、色谱柱、检测器，以便完成对样品的分离和分析。
B. 载气的作用是与样品发生化学反应，流经汽化室、色谱柱、检测器，以便完成对样品的分离和分析
C. 载气的作用是溶解样品，流经汽化室、色谱柱、检测器，以便完成对样品的分离和分析
D. 载气的作用是吸附样品，流经汽化室、色谱柱、检测器，以便完成对样品的分离和分析
【多选题】
下列关于空心阴极灯使用描述正确的是___。
A. 空心阴极灯发光强度与工作电流有关
B. 增大工作电流可增加发光强度
C. 工作电流越大越好
D. 工作电流过小，会导致稳定性下降
【多选题】
在原子吸收光谱法测定条件的选择过程中，下列操作正确的是___。
A. 在保证稳定和合适光强输出的情况下，尽量选用较低的灯电流
B. 使用较宽的狭缝宽度
C. 尽量提高原子化温度
D. 调整燃烧器的高度，使测量光束从基态原子浓度最大的火焰区通过
【多选题】
用相关电对的电位可判断氧化还原反应的一些情况，它可以判断___。
A. 氧化还原反应的方向
B. 氧化还原反应进行的程度
C. 氧化还原反应突跃的大小
D. 氧化还原反应的速度
【多选题】
膜电位的建立是由于___。
A. 溶液中离子与电极膜上离子之间发生交换作用的结果
B. 溶液中离子与内参比溶液离子之间发生交换作用的结果
C. 内参比溶液中离子与电极膜上离子之间发生交换作用的结果
D. 溶液中离子与电极膜水化层中离子之间发生交换作用的结果
【多选题】
气相色谱法中一般选择汽化室温度___。
A. 比柱温高30～70℃
B. 比样品组分中最高沸点高30～50℃
C. 比柱温高30～50℃
D. 比样品组分中最高沸点高30～70℃
【多选题】
使用相对保留值定性分析依据时，选择参照物（S）应注意___。
A. 参照物峰位置与待测物相近
B. 参照物与样品各组分完全分离
C. 参照物应当是容易得到的纯品
D. 参照物保留时间越小越好
【单选题】
下列实验操作中，正确的是___
A. 把pH试纸浸入待测溶液中，测定溶液的pH
B. 称NaOH固定质量时。将NaOH固体放在垫有滤纸的托盘上进行称量
C. 苯酚沾在皮肤上，应立即用酒精清洗
D. 浓硫酸溅在皮肤上，应立即用烧碱溶液冲洗
【单选题】
下列实验操作中。不正确的是___
A. 用分液漏斗分离除去溴苯中混入的溴
B. 用渗析法除去Fe（OH）3，胶体中的Cl-离子
C. 除去溴乙烷中的乙醇，用水洗后，再用分液漏斗分离
D. 用盐析法分离硬脂酸钠和甘油
【单选题】
提纯含有少量硝酸钡杂质的硝酸钾溶液，可以使用的方法为___
A. 加入过量碳酸钠溶液，过滤．除去沉淀，溶液中补加适量硝酸
B. 加入过量硫酸钾溶液，过滤，除去沉淀，溶液中补加适量硝酸
C. 加入过量硫酸钠溶液，过滤，除去沉淀，溶液中补加适量硝酸
D. 加入过量碳酸钾溶液，过滤，除去沉淀，溶液中补加适量硝酸
【单选题】
下列操作中错误的是___
A. 除去乙酸乙酯中的少量乙酸：加入乙醇和浓硫酸．使乙酸全部转化为乙酸乙酯
B. 除去苯中的少量苯酚：加入NaOH溶液，振荡、静置分层后，除去水层
C. 除去CO2中的少量S02：通过盛有饱和NaHCO3溶液的洗气瓶
D. 提取溶解在水中的少量碘：加入CCl4，振荡、静置分层后。取出有机层再分离
【单选题】
某溶液含有较多的Na2SO4和少量的Fe2（SO4）3若用该溶液制取芒硝，可供选择的操作有()①加适量珥H2SO4溶液②加金属Na③结晶④加过量Na0H溶液⑤加强热脱结晶水⑥过滤。正确的操作步骤是___
A. ②⑥③
B. ④⑥①③
C. ④⑥③⑤
D. ②⑥①③⑤
【单选题】
为实现中国2000年消除碘缺乏病的目标．卫生部规定食盐必须加碘。其中的碘以碘酸钾(KIO3)形式存在。巳知在溶液中I03-可和I-‘发生反应：I03-+5I-+6H+=3I2+3H20根据此反应．可用试纸和一些生活中常见的物质进行实验。证明在食盐中存在I03-；。可供选用的物质有：①自来水．②蓝色石蕊试纸。③碘化钾淀粉试纸．④淀粉，⑤食糖．⑥食醋⑦白酒。进行上述实验时必须使用的物质是___
A. ①③
B. ③⑥
C. ②④⑥
D. ①②④⑤⑦
【单选题】
下列各组溶液，不用其它试剂。就可以将它们区别开的是___
A. 盐酸氢氧化钠碳酸钠硫酸钠
B. 盐酸硝酸铵氢氯化钠硝酸钠
C. 氢氧化钠硝酸镁碳酸钠硫酸氢钠
D. 氯化钡硫酸钠氯化钙硝酸钙
【单选题】
实验室进行NaCl溶液蒸发时，一般有以下操作过程①放置酒精灯②固定铁圈位置③放上蒸发皿④加热搅拌⑤停止加热、余热蒸干其正确的操作顺序为___
A. ②③④⑤
B. ①②③④⑤
C. ②③①④⑤
D. ②①③④⑤
【单选题】
用某种仪器量取液体体积时，平视时读数为nmL,仰视时读数为xmL,俯视时读数为ymL,若X＞n＞y，则所用的仪器可能为___
A. 量筒
B. 容量瓶
C. 滴定管
D. 以上均不对
【单选题】
用pH试纸测定某无色溶液的pH值时，规范的操作是___
A. 将pH试纸放入溶液中观察其颜色变化,跟标准比色卡比较
B. 将溶液倒在pH试纸上，跟标准比色卡比较
C. 用干燥的洁净玻璃棒蘸取溶液，滴在pH试纸上，跟标准比色卡比较
D. 在试管内放入少量溶液、煮沸。把pH试纸放在管口，观察颜色。跟标准比色卡比较
【单选题】
下列每组各有三对物质，它们都能用分液漏斗分离的是___①乙酸乙酯和水，酒精和水，苯酚和水②二溴乙烷和水，溴苯和水，硝基苯和水③甘油和水，乙醛和水，乙酸和乙醇④油酸和水，甲苯和水，乙烷和水
A. ①②
B. ②④
C. ③④
D. ①②④
【单选题】
为了除去C02中的02、S02、H20(g)等杂质，可用①NaHC03饱和溶液②浓硫酸③加热的网，通过以上试剂顺序净化效果最好的是___
A. ②③①
B. ③②①
C. ②①③
D. ①②③
【单选题】
利用下述方法除去氮气中所含的杂质(HCl，H2，H2S)以得到干燥纯净氮气，在下列各步中应采用的正确顺序是___①通过装有变色硅胶的干燥管②通过氢氧化钠溶液③通过加热的氧化铜
A. ①②③③
B. ②①③①
C. ②③③①
D. ③②①③
【单选题】
关于粗盐提纯的下列说法正确的是___
A. 溶解粗盐时，应尽量使溶液稀些，防止食盐不全溶解
B. 滤去不溶性杂质以后，将滤液移至坩埚内加热浓缩
C. 当蒸发到剩有少量液体时，停止加热，利用余热将液体蒸干
D. 将制得的晶体转移到新制过滤器中用大量水进行洗涤
【单选题】
下列实验操作中错误的是___
A. 分液时，分液漏斗中下层液体从下口放出，上层液体从上口倒出。
B. 蒸馏时，温度计水银球靠近蒸馏烧瓶支管口。
C. 滴定时，左手控制滴定管活塞，右手握持锥形瓶，边滴边振荡，眼睛注视滴定管中的液面。
D. 称量时，称量物放在称量纸上，置于托盘天平的左盘，砝码放在称量纸上置于托盘天平的右盘中。
【单选题】
常温下，下列各组物质不能用一种试剂通过化学反应区别的是___
A. MnO2CuOFeO
B. (NH4)2SO4K2SO4NH4CI
C. AgNO3KNO3Na2CO3
D. Na2CO3NaHCO3K2CO3
【单选题】
为确定下列置于空气中的物质是否变质，所选检验试剂（括号内物质）不能达到目的的是___
A. Na2SO3溶液（BaCI2)
B. FeCI2溶液（KSCN）
C. KI（淀粉溶液）
D. HCHO溶液（石蕊试液）
推荐试题
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
A storage administrator is not seeing full utilization of all bandwidth from an ESXi host. The vSphere administrator observes the adapter details, as shown in the Exhibit. What is the probable cause of this issue?___
A. Another path needs to be used to allow full utilization of the bandwidth.
B. The array is not setup to use the correct multipathing policy.
C. There are no virtual machines on the host.
D. No traffic is being sent across it because a path failed.
【单选题】
An administrator has just completed performing an interactive installation of ESXi 6.x and is booting the host. How is the network initially configured?___
A. The network is configured by Automatic Private IP Addressing (APIPA).
B. The network is configured based on the settings detected in DNS.
C. The network is configured with the address as specified in the installer.
D. The network is automatically configured by DHCP.
【单选题】
You have just installed an ESXi 6.x Host. As part of your company security regulations, a security banner must be presented on the console of the host. How can this action be accomplished?___
A. Configure the Advanced Settings > Annotations screen of the ESXi host.
B. This is configured from the Direct Console User Interface configuration menu.
C. It is not possible to configure a security banner for the ESXi host.
D. From vCenter Server, this setting is configured globally in the vCenter Server configuration.
【单选题】
An administrator is only able to see the Health Badge when using the vRealize Operations user interface. What is the likely cause of this behavior?___
A. The vRealize Operations Foundation License is in use.
B. The vmware-sps service failed to start.
C. The vRealize Operations Standard License is in use.
D. The vmware-rbd-watchdog service failed to start.
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets either of these conditions: <High virtual CPU> <High active memory consumption.> <The alarm is only triggering when both of the conditions are met.> What can be done to correct the alarm behavior?___
A. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory and link them together with ESXCLI.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is attempting to restore a number of files in a directory within the Operating System of a virtual machine. How can the administrator restore the files from a previous backup? ___
A. Use the File Level Restore option from the selected backup of the virtual machine in the vSphere Web Client.
B. Connect to the File Level Restore tool from a web browser in the virtual machine.
C. Connect to the File Level Restore tool from the VMware
D. ata Protection appliance.
【单选题】
After selecting an object in vRealize Operations, how can a user compare the badge values of related child objects? ___
A. Use the Scoreboard tab
B. Use the Relationship tab
C. Use the Members tab
D. Use the Overview tab
【单选题】
You want to deploy a vApp and dynamically assign IP addresses without a DHCP server on the network. Which action would you take to accomplish this task? ___
A. Enable IP pools.
B. Configure a local DHCP server in the vApp.
C. Enable NAT on the vApp router.
D. Configure the guest OS for workgroup and WINS.
【单选题】
What is the optimal configuration when building a virtual machine for a single-threaded Windows application? ___
A. Deploy single-threaded applications on uniprocessor virtual machines.
B. Deploy single-threaded applications on symmetric multi-processor virtual machines.
C. Tune single-threaded applications to take advantage of symmetric multi-processor resources.
D. Tune Single-threaded applications at the hypervisor level.
【单选题】
An administrator has created the resource pool configuration shown in the Exhibit. Based on the exhibit, which virtual machine(s) can be successfully powered on? ___
A. VM-M1 only
B. VM-K1 only
C. VM-K1 and VM-K2 only
D. VM-K1, VM-K2, and VM-M1
【单选题】
Which vSphere 6 Enterprise Edition feature will allow an organization to ensure that critical multi-threaded applications have the maximum possible uptime? ___
A. Fault Tolerance
B. High Availability
C. Distributed Resource Scheduler
D. App HA
【单选题】
An administrator has a virtual machine that requires four times the compute resources than other virtual machines on the same ESXi 6.x host. How should the administrator configure the virtual machine settings, in order to be prepared for any resource contention? ___
A. Set the shares of the priority virtual machine to High and the rest to Low.
B. Set the shares of the priority virtual machine to High.
C. Set the shares of the priority virtual machine to High and the rest to Normal.
D. Set the shares of the priority virtual machine to Normal and the rest to Low.
【单选题】
Which type of Adapter does not require vmkernel networking? ___
A. Independent Hardware iSCSI Adapter
B. Dependent Hardware iSCSI Adapter
C. Software iSCSI Adapter
D. Software FCoE Adapter
【单选题】
During the installation of ESXi 6.0, the following error message is reported: Hardware Virtualization is not a feature of the CPU, or is not enabled in the BIOS. Which condition would generate this message? ___
A. LAHF/SAHF is not enabled in the BIOS.
B. NX/XD is not enabled in the BIOS.
C. SSE3 is not enabled in the BIOS.
D. Hyperthreading is not enabled in the BIOS.
【单选题】
An administrator is unable to login to vCenter Server when using the vSphere web client. The administrator successfully accessed vCenter Server using the client earlier the same day. What is the most appropriate first step the administrator should take to resolve this issue? ___
A. Verify the web browser being used has Adobe Flash plugin version 11.5 or later
B. Verify the vCenter Single Sign-On service is running on the vCenter Server
C. Verify the vSphere Web Server service is running on the vCenter Server
D. Verify the administrator has permissions configured in vCenter Server
【单选题】
An administrator has configured an alarm to be notified when a virtual machine meets two conditions: <high virtual CPU> <high active memory consumption> The alarm is malfunctioning and triggering when either condition is met instead of both. What can be done to correct the issue? ___
A. Edit the alarm and select Trigger if ALL of the following conditions are satisfied.
B. Edit the alarm and select Trigger if ANY of the following conditions are satisfied.
C. Create two separate alarms, one for CPU and one for memory.
D. Delete the existing alarm and create a new event based alarm.
【单选题】
What must be enabled to ensure that VM Component Protection (VMCP) works in a High Availability cluster? ___
A. VMware Tools Virtual Machine Communication Interface (VMCI)
B. Fault Tolerance
C. Atomic Test and Set (ATS)
D. All Paths Down (APD) Timeout
【单选题】
An administrator wants to add a web server to an existing multi-tier application consisting of three virtual machines: <A web server> <A database server An application server> The web server should be added to the application when the primary web server reaches: <70% vCPU utilization> <55% active memory> Which option will achieve this result? ___
A. Create a virtual machine alarm with an action to run a script that starts a new instance of the web server.
B. Create a host cpu and memory alarm with an action to run a script that starts a new instance of the webserver.
C. Configure HA application monitoring for the web server and set it to trigger deployment of a new instance of the web server.
D. Configure Fault Tolerance on the virtual machine and leave the secondary machine disabled until needed.
【单选题】
An administrator has an application that requires connection directly to PCI devices through a virtual machine. What is a limitation of this configuration? ___
A. Devices must be reserved for PCI passthrough on at least one host on which the virtual machine will run.
B. Snapshots are not supported with DirectPath I/O passthrough devices.
C. A maximum of 18 PCI vSphere
D. irectPath devices can be added to a virtual machine.
【单选题】
The vSphere administrator is configuring directory services for an ESXi host: What should the vSphere administrator do to configure the host to use CAM services? ___
A. Check the Use vSphere Authentication Proxy checkbox.
B. Set Select Directory Service Type to CAM services.
C. Specify CAM$ for the
D. omain.
【单选题】
Which statement is true regarding the licensing of vCenter Server? ___
A. The license for vCenter Server must be provided at the time of installation.
B. Changing the license assigned to vCenter Server requires a restart of the vCenter Server service.
C. Virtual machines can still be powered on if the vCenter Server license expires.
D. Licensing for a single vCenter Server installation is determined by the number of managed virtual machines.
【单选题】
When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected? ___
A. 1 min
B. 5 min
C. 10 min
D. 15min
【单选题】
A developer needs to create a multi-tier development stack for a home lab. Which vSphere product will support the architecture required for the least software cost? ___
A. vSphere Hypervisor
B. vSphere Essentials
C. VMware Player
D. VMware Workstation
【单选题】
An administrator is installing Windows into a virtual machine. The DVD has been mounted on the Host and configured for the virtual machine as shown in the Exhibit. Based on the exhibit, when the virtual machine is booted, why would it attempt to search for a PXE server? ___
A. The CD/DVD device is not connected.
B. The ISO is in the incorrect storage location.
C. The OS minimum requirements have not been met.
D. The CD/DVD device is not set to Client Device.
【单选题】
What component must be installed prior to deploying a vCenter Server in vSphere 6.x? ___
A. vCenter Identity Services
B. Platform Services Controller
C. vCenter Single Sign-On
D. Client Integration Plug-In
【单选题】
What is a valid plug-in status for a plug-in that has been added to a vSphere client? ___
A. Disabled
B. Unknown
C. Stopped
D. Installed
【单选题】
Users of an application are reporting performance issues. The following performance values are observed in the vSphere Web Client: <Host CPU utilization is 90%> <Virtual Machine memory utilization is consistently greater than 90% CPU Ready values are higher than 20%> What could be the cause of the application performance issue? ___
A. The host is lacking the CPU resources required to meet the demand.
B. The host is lacking the memory resources required to meet the demand.
C. The virtual machine is lacking the CPU resources required to meet the demand.
D. The virtual machine is lacking the memory resources required to meet the demand.
【单选题】
An administrator creates an ESXi cluster using vSphere Auto Deploy. The ESXi hosts are configured to get a management IP address from a DHCP server. The administrator needs to troubleshoot the management network on one of the hosts. Which DCUI option should the administrator use to renew the DHCP lease? ___
A. Restart Management Network
B. Restore Network Settings
C. Test Management Network
D. Configure Management Network
【单选题】
An administrator is re-provisioning an ESXi host and moving it to another datacenter. Which DCUI option should the administrator use to revert the system configuration to the default settings? ___
A. Reset System Configuration
B. Rebuild Default System Configuration
C. Revert System Configuration
D. Renew Default System Configuration
【单选题】
An administrator has just completed installing an ESXi 6.x host, but doesn't know what address has been configured. Where is the ESXi host IP address configured? ___
A. RVC console
B. Direct Console User Interface
C. vSphere Web Client
D. vSphere Client
【单选题】
When is it possible to place a VMFS5 datastore in maintenance mode? ___
A. When it is a member of a Storage DRS cluster
B. When it is a member of Virtual SAN cluster
C. When it is a member of a multi-extent datastore
D. When it is a member of a Virtual Volume
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Immediately after installing ESXi, an administrator observes that the Configure Lockdown Mode option is grayed out in the Direct Console User Interface (DCUI). What is the most likely explanation? ___
A. The host has not yet been added to a vCenter Server.
B. The BIOS on the host does not have NX/XD enabled.
C. The ESXi host is running in evaluation mode.
D. The host requires a reboot before this feature is available.
【单选题】
Which Single Sign-On deployment mode should an administrator use for two 6.x vCenter Servers configured with linked mode? ___
A. Basic Single Sign-On with vCenter Server Heartbeat
B. Multisite Single Sign-On
C. Basic Single Sign-On
D. Single Sign-On with Linked Mode
【单选题】
What is required when changing a virtual machine name using the vSphere Web Client? ___
A. Verify connectivity to the ESXi host where the virtual machine is running and its inventory list is accessible.
B. Verify in which datastore the virtual machine resides and that you have access and its inventory list is accessible.
C. Verify that virtual machine files are stored in the same datastore and can be accessed in the datastore browser list.
D. Verify the virtual machine is not running in Fault Tolerant mode and that it is not in a Distributed Resource Scheduler cluster.
【单选题】
An administrator deploys vRealize Operations into a vSphere 6.x environment. After the deployment, the administrator notices that badges are not appearing. What is a likely cause of this behavior? ___
A. Badges do not appear until you register vRealize Operations with vCenter Server.
B. Badges do not appear until you register a vCenter Server in vRealize Operations.
C. The vRealize Operations appliance needs to be redeployed.
D. The vCenter Server appliance needs to be redeployed.
【单选题】
How are ports scaled on vSphere Standard Switches (vSS)? ___
A. Ports on a vSS can be dynamically scaled up and down.
B. Ports on a vSS can only be statically scaled up or down.
C. Ports on a vSS can only be dynamically scaled down.
D. Ports on a vSS can only be dynamically scaled up.
【单选题】
A High Availability (HA) cluster is configured to respond to a given number of host failures. The cluster contains virtual machines configured with these settings: VM1 has a 1GHz CPU reservation and no Memory reservation VM2 has a 2GHz CPU reservation and no Memory reservation VM3 has no CPU reservation and no Memory reservation . Given this information, what is the correct slot size for the cluster? ___
A. The CPU Reservation should be set to 32MHz and the memory reservation should be set to 32MB plus memory overhead.
B. The CPU reservation should be set to 1 GHz and the memory reservation should be set to 0MB plus memory overhead.
C. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 0MB plus the virtual machine memory overhead.
D. The CPU reservation should be set to 2 GHz, and the memory reservation should be set to 32MB, plus the virtual machine memory overhead.
