【单选题】
安全阀应该垂直装在汽包的___位置。
A. 最高
B. 最低 C.中间
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
A
解析
暂无解析
相关试题
【单选题】
水垢是水中___离子的盐类形成的。
A. 所有金属
B. 钙镁 C.铜铁答文:B
【单选题】
裂解炉辐射段炉管所用的HP-40材质为___。
A. 25Cr-35Ni
B. 20Cr-32Ni
C. 25Cr-20Ni
D. 25Cr-40Ni
【单选题】
不适宜做调节流体流量及输送含颗粒物料的阀门是___。
A. 旋塞阀
B. 截止阀
C. 闸阀
【单选题】
一般情况下,当裂解炉炉管渗碳大于___时,应考虑更换炉管。
A. 60%
B. 70%
C. 80%
D. 40%
【单选题】
下列不适合做裂解原油的是___。
A. 石脑油
B. 减压轻柴油
C. 常压轻柴油
D. 裂解汽油
【单选题】
在列管式换热器中,最常用的流体流向是___。
A. 逆流
B. 错流
C. 并流
【单选题】
以下哪种泵启泵时出口阀可关死___。
A. 离心泵
B. 往复泵
C. 计量泵
D. 齿轮泵
【单选题】
离心泵盘不动车原因正确的为___。
A. 连轴节松动
B. 油箱液位太高
C. 泵出口有压力
D. 介质温度过高 C
【单选题】
现场导淋开启困难的原因有___。
A. 阀杆螺纹锈蚀
B. 锁紧螺母松动
C. 填料失效
【单选题】
下列物质属于有机物的是:___。
A. CO
B. H2CO3
C. CH3COOH
D. Na2CO3 C
【单选题】
尾油的标准横跨温度为___。
A. 593℃
B. 679.5℃
C. 620℃
D. 559℃ D
【单选题】
按压力容器的设计压力,压力在___的为中压容器。
A. 1.6Mpa≤P<10Mpa
B. 10Mpa≤P<100Mpa
C. P≥100Mpa
【单选题】
正常生产时,裂解单元废气的来源有___。
A. 裂解炉
B. 裂解炉超高压蒸汽汽包间断排污罐放空
C. 透平驱动蒸汽及背压蒸汽排放
D. 火炬排放
【单选题】
下列现象是化学变化的是:___。
A. NaOH溶液的蒸发
B. 裂解气的分离
C. 氢气的压缩
D. 乙烯的聚合
【单选题】
在其它条件不变的情况下,升高温度会使反应平衡向___方向移动。
A. 放热
B. 吸热
C. 既不吸热,也不放热
【单选题】
在其它条件不变的情况下,增压气体反应的总压力,平衡将向气体分子数___的方向移动。
A. 增加
B. 减少
C. 不变
【单选题】
下列灭火器中,不适用于电器着火的是___。
A. 泡沫灭火器
B. 干粉灭火器
C. 1211灭火器
【单选题】
在列管式换热器中,最常用的流体流向是___。
A. 逆流
B. 错流
C. 并流 .
【单选题】
F-002炉共有___个燃烧器.
A. 8
B. 16
C. 32
【单选题】
一般规定原料中硫含量≥___时,可不必向原料中注硫。
A. 40PPm
B. 100PPm
C. 60PPm .
【单选题】
原料与成本的关系是___。
A. 原料越重,成本越高
B. 原料轻重与成本无关
C. 一般地,原料越重,原料费用所占成本的比例越大
【单选题】
控制裂解炉横跨段温度的主要目的是___。
A. 降低排烟温度,提高炉子热效率
B. 提高辐射段热负荷
C. 防止原料在对流段结焦 .
【单选题】
乙烯装置能源消耗集中在裂解炉区的比例为___。
A. 60-70%
B. 70-80%
C. 80-90% .
【单选题】
乙烯装置中的隔油池属于废水三级处理中的___。
A. 初级处理
B. 二级处理
C. 三级处理
【单选题】
当积分调节作用达到稳定时,偏差为___。
A. 最小
B. 等于零
C. 最大
【单选题】
塔内上升气速直接影响到传质效果,塔内最大蒸汽上升速度不得超过___。
A. 空塔速度
B. 液泛速度
C. 1/2空塔速度D. 1/2液泛速度
【单选题】
含油废水中,可用浮选法分离的油类为___。
A. 溶解状态
B. 悬浮状态
C. 乳化状态
【单选题】
可燃液体在管道中的安全流速可用式___计算。
A. V=0.6
B. V=0.8
C. V=0.6
【单选题】
裂解炉汽包连续排污的目的是___。
A. 正常控制汽包的液位
B. 事故状态保证汽包液位
C. 防止汽包液位过高
D. 防止杂质在汽包内积累
【单选题】
下列各项关于裂解深度的叙述中,不正确的是___。
A. 裂解深度就是裂解反应进行的程度
B. 裂解深度高,原料转化率越高
C. 裂解深度通常是通过控制裂解炉出口温度来实现的
D. 一般来说,裂解深度越高,液态产物越多
【单选题】
急冷锅炉出口设计温度是由___决定的。
A. 原料类型
B. 裂解炉炉型
C. 裂解炉流出物的露点
【单选题】
P-102出口压力自启动值是多少___。
A. 980KPa
B. 1100 KPa
C. 450 KPa 答文:A
【单选题】
在降低裂解炉负荷时,一般要求投油量不得低于设计值的___。
A. 70%
B. 60%
C. 80%
D. 90%
【单选题】
裂解炉F-001燃料气压力低低联锁值为:___。
A. 10KPa
B. 13 KPa
C. 4 KPa
D. 20 KPa
【单选题】
汽油分馏塔塔顶温度过高会直接影响___。
A. 急冷水塔塔顶温度
B. 汽油分馏塔塔压差
C. 汽油干点
D. 裂解燃料油外送量
【单选题】
备用泵盘车的方向一般是___。
A. 顺时针方向
B. 逆时针方向
C. 泵的运转方向
D. 无特殊规定
【单选题】
泡沫灭火器适用于___。
A. 可燃性气体
B. 油类着火
C. 电气火灾
【单选题】
F-002 NAP烃进料压力低低(2/3)的报警值、联锁值分别为 ___。
A. 0.77MPa,2.0MPA
B. 0.75MPa,0.7MPA
C. 0.45MPa,0.4MPa
【单选题】
裂解炉长明灯压力低低的报警、联锁值分别是___。
A. 0.04MPa,0.03MPA
B. 0.2MPa,0.1MPA
C. 0.4MPa,0.35MPa
【单选题】
下列各项关于现场动火要求的叙述正确的是___。
A. 几个动火项目可办一个动火证
B. 动火分析只用作设备,管线内部即可
C. 动火监护人无权终止不合要求动火
D. 动火分析要求统一规定为管内≤0.1%,管外≤0.2%
推荐试题
【填空题】
27.20世纪80年代末、90年代初,随着东欧剧变和苏联解体,持续近半个世纪的冷战格局被打破。 “___ ” 是当前乃至今后相当长时期内世界主要战略力量对比的总体态势和总体特征。
【填空题】
28.进入新世纪我国周边外交政策和目标的重要内容是“___ 、___ 、___ ”。
【填空题】
29.我国在有关南海问题上一贯坚持“___、___、___”的原则。
【填空题】
30.决定不同时期各国战略的内容和特点主要包括三个方面:___、___ 、___ 。
【填空题】
31.事实表明,___是阻挠台湾问题解决的最大障碍。
【填空题】
32.我军积极防御的军事战略要处理好防御与进攻的关系,___的关系,军事与政治的关系。
【填空题】
33.新安全观的核心是___、___、 ___ 和 ___ 。
【填空题】
34.人类战争在经过 ___ 、___、___ 、___几个阶段后,正在进入信息化战争阶段。
【填空题】
35.六维空间是指___、___ 、___ 、___ 、___ 、___。
【填空题】
36. 中国人民解放军六个兵种分别是___、___、___、___、___、___。
【填空题】
37.中国人民解放军五大战区分别是___、___、___、___、___。.
【填空题】
38.世界新军事变革不断深化,打赢 ___ 战争成为各国关注的焦点
【填空题】
39.每年九月的___星期六为“全民国防教育日”。
【填空题】
40.制导技术按照不同控制导引方式可概括为 ___ 、 ___ 、 ___ 、 ___ 和___等五种方式。
【填空题】
41.凭借着___与 ___ 提供的“千里眼”、“顺风耳”,军事指挥员可以迅速、准确、全面地掌握敌方的情况,识别、跟踪和预测敌方未来的行动,从而为克敌制胜创造有利条件。
【填空题】
42.八国联军于___年,发动了侵华战争。
【填空题】
43.1957年10月4日,苏联把世界上第一颗 ___ 送入地球近地轨道.
【填空题】
44.中央军委下属机关有___个部<厅>、___个委员会、___个直属机构。
【填空题】
45.___是国防强大的基础。
【填空题】
46.天基武器系统主要指攻击对方航天器用的卫星和卫星平台,包括 ___ 、 ___和___ 等。
【填空题】
47.中国人民解放军海军成立于___年。
【填空题】
48.新概念武器主要有 ___ 、___、 ___ 、 ___ 、___ 等。
【填空题】
49.核武器具有____、冲击波、____ ___、核电磁脉冲和放射性沾染等五种杀伤破坏因素。
【填空题】
50.精确制导技术是指采用高技术直接命中概率超过___以上的武器。
【单选题】
What is an example of social engineering?___
A. gaining access to a computer by observing the user login credentials
B. gaining access to a build through an unguarded entrance
C. gaining access to a server by using a USB stick
D. gaining access to a server room by posing as local IT
【单选题】
Which type of Layer 2 attack enables the attacker to intercept traffic that is intended for one specific recipient?___
A. BPDU attack
B. DHCP starvation I LAB
C. MAC address spoofing
D. CAM table overflow
【单选题】
Which about nested policy maps in a zone-based firewall is true ?___
A. They are limited to two leve ls in a hierarchical policy
B. Parent policies are previously defined policies that are defined by using the service policy command
C. A child policy is a new policy that uses a pre-existing policy.
D. A child policy is a new that uses a pre-existing policy
【单选题】
In which configuration do you configure the ip ospf authentication key 1 command?___
A. routing process
B. interface
C. privileged
D. global
【单选题】
Which statement about command authorization and security contexts is true?___
A. If command authorization is configured, it must be enabled on all contexts.
B. The change to command invokes a new context session with the credentials of the currently
C. AAA settings are applied on a per-context basis
D. The enable. 15 user ang admins with chang to permission ha e dfferent command authorization levels pertontext
【单选题】
Which command do you enter to enable authentication for OSPF on an interface?___
A. router(config-if)#ip ospf message-digest-key 1 md5 CIS COPASS
B. router(config-if)#ip ospf authentication message-digest
C. router(config-if)#ip ospf authentication-key CISCOPASS
D. router(config-if)#area 0 authentication message-digest
【单选题】
What feature defines a campus area network?___
A. It has a single geographic location
B. It lacks external connectivity.
C. It has a limited number of segments.
D. It has limited or restricted Internet access
【单选题】
Which type of attack most commonly involves a direct attack on a network?___
A. :phishing
B. Trojan horse
C. denial of service
D. social engineering
【单选题】
What information does the key length provide in an encryption algorithm?___
A. the cipher block size
B. the hash bloc k size
C. the number of permutations
D. the packet size
【单选题】
How do you verify TaCACS+ connectivity to a device?___
A. You successfully log in to the device by using the local credentials
B. You connect via console port and receive the login prompt.
C. You connect to the device using SSH and receive the login prompt.
D. You successfully log in to the device by using ACS credentials
【单选题】
Which term best describes the concept of preventing the modification of data in transit and in storage?___
A. availability
B. confidentially
C. fidelity
D. integrity
【单选题】
Which loS command is used to define the authentication key for ntp?___
A. switch(config )#ntp authentication-key 1 mds Clcs
B. switch(config )#ntp authenticate
C. switch(config)#ntp trusted-key 1
D. switch(config)#ntp source 192.168.0.1
【单选题】
What is true about the cisco lOS Resilient Configuration feature ?___
A. The feature can be disabled through a remote session
B. There is additional space required to secure the primary cisco lOS image file.
C. The feature automatically detects image or configuration version mismatch.
D. Remote storage is used for securing files
【单选题】
When is the default deny all policy an exception in zone-based firewalls?___
A. when traffic terminates on the router via the self zone
B. when traffic traverses two interfaces in different zones
C. when traffic traverses two interfaces in the same zone
D. when traffic sources from the router via the self zone
【单选题】
.If an access port is assigned as an isolated port in a PVLAN, which network ports can it communicate with?___
A. promiscuous ports in the same PLVAN
B. isolated ports in the same PVLAN
C. all ports in the same PAVLAN at ILAR
D. all ports in the adjacent PVLAN
【单选题】
Which IPSEC mode is used to encypt traffic directly between a client and a server VPN endpoint?___
A. quick mode
B. transport mode
C. aggressive mode
D. tunnel mode