【多选题】
降低克劳斯尾气中硫化氢含量的方法是___。
A. 减少酸性气波动
B. 提高反应炉炉膛温度
C. 提高配风比
D. 提高克劳斯反应器进口温度
查看试卷,进入试卷练习
微信扫一扫,开始刷题
答案
ACD
解析
暂无解析
相关试题
【多选题】
克劳斯反应器床层温度的影响因素是___。
A. 反应器进口H2SSO2浓度变化
B. 催化剂活性
C. 反应器进口温度的变化
D. 系统压力的变化
【多选题】
溶剂发泡时的处理方法是___。
A. 添加适量的消泡剂
B. 加强溶剂过滤
C. 检查储罐氮封是否完好,防止空气漏入
D. 加水置换
【多选题】
酸性气原料突然中断的处理方法是___。
A. 改烧瓦斯
B. 时间长装置按紧急停工处理
C. 燃烧炉闷炉待料
D. 焚烧炉闷炉待料
【多选题】
脱硫剂富液与贫液主要区别有___。
A. 硫化氢浓度
B. 二氧化碳浓度
C. 烃浓度
D. 氮气浓度
【多选题】
尾气焚烧炉鼓风机停机时焚烧炉的工艺现象是___。
A. 进炉风量为零
B. 发生联锁自保
C. 炉膛压力升高
D. 炉膛熄火
【多选题】
硫磺排污时发现黑硫磺,其生成原因不正确的是___。
A. 原料带水
B. 燃烧炉瓦斯进炉阀门内漏
C. 原料带烃
D. 原料带胺
【多选题】
瓦斯带水的工艺现象___。
A. 炉膛火焰发红
B. 炉膛压力上升
C. 炉膛出口温度急剧下降
D. 如带水过多火焰熄灭
【多选题】
烟囱冒黑烟的原因是___。
A. 焚烧炉配风过小
B. 风机放空阀开度过大
C. 烟气量过大
D. 废热锅炉腐蚀
【多选题】
停仪表风的现象___。
A. 调节阀失灵
B. 操作参数变化较大
C. 调节阀开度为100%
D. 控制阀可以控制
【多选题】
烟道气温度高时的处理方法是___。
A. 烟道增加衬里
B. 开好克劳斯系统
C. 全开烟道进口蝶阀
D. 降低焚烧炉废热锅炉自发中压蒸汽压力
【多选题】
克劳斯反应器超温经常发生在___。
A. 开工时
B. 停工时
C. 配风比高时
D. 配风比低时
【多选题】
瓦斯带油,将会导致___。
A. 瓦斯减量而炉温下降
B. 瓦斯减量而炉温上升
C. 焚烧炉炉膛熄火
D. 阻火器失效
【多选题】
溶剂再生塔压力高的处理方法是___。
A. 检查是否克劳斯系统压力上升
B. 降低塔底蒸汽流量
C. 检查回流罐液面是否高
D. 提高回流量
【多选题】
溶剂再生塔压力高的危害是___。
A. 酸性气放火炬
B. 溶剂解吸效果变差
C. 溶剂老化
D. 溶剂浓度变低
【多选题】
停燃料气的处理方法是___。
A. 检查阻火器是否堵
B. 检查控制阀是否处于全关状态
C. 检查是否瓦斯分液罐是否满
D. 检查联锁是否完好
【多选题】
停高压除氧水对硫磺回收装置的影响是___。
A. 造成锅炉水位低
B. 损坏蒸汽过热器
C. 加工量降低
D. 对装置没有影响
【多选题】
在PID控制中,有___控制参数。
A. 比例度
B. 积分时间
C. 微分时间
D. 时间
【多选题】
酸性水脱气罐压力过低的原因___。
A. 脱气罐液面过低
B. 进料烃含量过小
C. 进料量小
D. 仪表故障
【多选题】
汽提塔塔顶压力低的原因是___。
A. 污水浓度高
B. 进料量小
C. 酸性气排出量大
D. 加热蒸汽量大
【多选题】
汽提塔底液面偏高的原因是___。
A. 加热蒸汽量大
B. 热进料量大
C. 净化水排出量小
D. 仪表失灵
【多选题】
汽提塔塔顶压力偏高的原因是___。
A. 加热蒸汽量大
B. 污水浓度高
C. 克劳斯系统压力高
D. 仪表失灵
【多选题】
汽提塔顶酸性气线堵的现象___。
A. 塔顶压力升高
B. 顶温下降
C. 酸性气流量降低
D. 塔顶压力下降
【多选题】
汽提塔顶酸性气线堵的的处理方法___。
A. 作紧急停工处理
B. 提高塔顶温
C. 用蒸汽吹扫堵塞管线
D. 加大塔顶回流
【多选题】
酸性水汽提装置瞬时停电或短时间停电的处理方法___。
A. 重沸器的蒸汽量调节阀关小
B. 关闭净化水出装置调节阀
C. 重新启动机泵
D. 检查原料水罐的液位情况
【多选题】
燃烧炉温度过高的原因有___。
A. 酸性气含烃类高
B. 酸性气中硫化氢浓度高
C. 配风偏大
D. 仪表失灵
【多选题】
使氧化铝型催化剂硫酸盐化,使其降低或丧失活性的主要毒害物质是___。
A. O2
B. SO3
C. NH3
D. H2S
【多选题】
锅炉用水水质不良对锅炉的危害有___。
A. 生锅炉结垢
B. 引起锅炉腐蚀
C. 影响蒸汽品质
D. 无影响
【多选题】
H2S/SO2在线分析仪发生故障,会产生___
A. H2S/SO2比值固定不变
B. 与采样分析的数据不一致
C. 尾气中二氧化硫含量上升
D. 副风不随 H2S/SO2比值的变化而变化
【多选题】
装置催化剂的物理失活主要有___
A. 积碳
B. 硫酸盐
C. 积硫
D. 热崩
【多选题】
用瓦斯升温过程中,燃烧炉或反应器温度偏高可以采取的措施正确的是___
A. 降低瓦斯量
B. 减少风量
C. 注氮气降温
D. 提高风量
【多选题】
硫磺装置酸气原料中主要杂质有___
A. 二氧化碳
B. 烃类
C. 氨盐
D. 水分
【多选题】
酸性气分液罐的作用___。
A. 脱油
B. 脱水
C. 脱烃
D. 缓冲
【多选题】
在酸气燃烧炉中发生的主要反应是___。
A. H2S+1/2O2=1/2S2+H2O
B. CH4+2O2=CO2+2H2O
C. 2H2S+3O2=2SO2+2H2O
D. COS+H2O=CO2+H2S
【多选题】
硫磺回收装置的污染源有___。
A. 废催化剂
B. 废气
C. 含硫污水
D. 噪音
【多选题】
锅炉煮炉在炉水中加入药剂,然后将炉水煮沸,使锅炉内金属表面的污垢和铁锈溶解疏松和脱落下来,以___。
A. 防止受热面腐蚀
B. 防止受热面过热
C. 保证炉水品质
D. 保证蒸汽的品质
【多选题】
常用煮炉用药剂有___。
A. 磷酸三钠
B. 硫酸钠
C. 氢氧化钠
D. 氯化钠
【多选题】
点炉升温前应满足以下___准备工作。
A. 瓦斯采样分析氧含量,确保瓦斯合格
B. 废热锅炉已进水至指定液位,并用蒸汽加热
C. 准备好升温曲线
D. 打火系统检查正常
【多选题】
溶剂再生塔顶回流罐液面上涨较快可能的原因是___。
A. 溶剂回流泵运行不正常
B. 仪表故障
C. 富液量波动
D. 溶剂再生塔冲塔
【多选题】
原料气中含有大量水,处理方法是___。
A. 适当加大配风
B. 适当降低处理量
C. 适当提高处理量
D. 加强分液罐脱水
【多选题】
二级反应器床层温度上升的原因是___。
A. 一级反应器效果差
B. 过程气中氧含量上升
C. 过程气中二氧化硫含量上升
D. 伴热蒸汽压力升高
推荐试题
【单选题】
There are two versions of IKE:IKEv1 and IKEv2. Both IKEv1 and IKEv2 protocols operate in phases IKEv1 operates in two phases. IKEv2 operates in how many phases?___
A. 2
B. 3
C. 4
D. 5
【单选题】
What does the dh group refer to?___
A. length of key for hashing C
B. length of key for encryption
C. tunnel lifetime key
D. length of key for key exchange
E. length of key for authentication
【单选题】
Which path do you follow to enable aaa through the SDM ?___
A. Configure Tasks > AAA
B. Configure > Addition Authentication > AAA
C. Configure > AAA
D. Configure > Additional Tasks > AAA
E. Configure Authentication > AAA
【单选题】
which technology cloud be used on top of an MPLS VPN to add confidentiality ?___
A. IPsec
B. 3DES
C. AES
D. SSL
【单选题】
Which term is most closely aligned with the basic purpose of a SIEM solution? ___
A. Non-Repudiation
B. Accountability
C. Causality
D. Repudiation
【单选题】
You have just deployed SNMPv3 in your environment, Your manager asks you to make sure that our SNMP agents can only talk to the SNMP Manager. What would you configure on your SNMI agents to satisfy this request?___
A. A SNMP View containing the SNMP managers
B. Routing Filter with the SNMP managers in it applied outbound
C. A standard ACL containing the SNMP managers applied to the SNMP configuration
D. A SNMP Group containing the SNMP managers
【单选题】
Which feature prevents loops by moving a nontrunking port into an errdisable state when a BPDU is received on that port?___
A. BPDU filte
B. DHCP snooping
C. BPDU guard
D. Port Fast
【单选题】
Which command enables port security to use sticky MAC addresses on a switch?___
A. switchport port-security violation restrict
B. switchport port-security mac-address sticky
C. switchport port-security violation protect
D. switchport port-security
【单选题】
When you edit an IPS subsignature, what is the effect on the parent signature and the family of subsignatures?___
A. The change applies to the parent signature and the entire family of subsignatures
B. The change applies to the parent signature and the subsignature that you edit
C. The change applies only to subsignatures that are numbered sequentially after the subsignature that you edit
D. Other signatures are unaffected, the change applies only to the subsignature that you dit
【单选题】
Which type of mechanism does Cisco FirePOWER de ploy to protect ag detected moving across other networks?___
A. antivirus scanning
B. policy-based
C. reputation-based
D. signature-based
【单选题】
What action must you take on the ise to blacklist a wired device?___
A. Locate the switch through which the device is connected and push an a cl restricting all access by the device
B. Issue a CoA request for the de vice's mac address to each access switch in the network
C. Revoke the device's certificate so it is unable to authenticate to the network
D. Add the device's MAc address to a list of black listed devices
【单选题】
Which type of firewall can perform deep packet inspection?___
A. packet-filtering firewall
B. stateless firewall
C. application firewall
D. personal firewall
【单选题】
What is the main purpose of Control Plane Policing?___
A. to prevent exhaustion of route-proce ssor resources
B. to organize the egress packet queues
C. to define traffic classes
D. to maintain the policy map
【单选题】
Which attack can be prevented by OSPF authentication?___
A. smurf attack
B. IP spoofing attack
C. denial of service attack
D. buffer overflow attack
【单选题】
What is the best definition of hairpinning?___
A. ingress traffic that traverses the outbound interface on a device
B. traffic that enters one interface on a device and that exits through another interface
C. traffic that enters and exits a device through the same interface
D. traffic that tunnels through a device interface
【单选题】
Which SNMPv3 security level provides authentication using HMAC with MD5, but does not use encryption?___
A. authPriv
B. authNo Priv
C. noAuthNoPriv
D. NoauthPriv
【单选题】
You have implemented a dynamic blacklist, using security intelligence to block illicit network activity. However, the blacklist contains several approved connections that users must access for usiness pur poses. Which action can you take to retain the blacklist while allowing users to access the approve d sites?___
A. Create a whitelist and manually add the approved addresses.
B. Disable the dynamic blacklist and deny the specif ic address on a whitelist while permitting the others
C. Edit the dynamic blacklist to remove the approved addresses
D. Disable the dynamic blacklist and create a static blacklist in its place
【单选题】
When connecting to an external resource,you must change a source IP address to use one IP address from a range of 207.165.201.1 to 207.165.1.30. Which option do you implement ?___
A. dynamic source NAT that uses an IP ad dress as a mapped source
B. static destination NAT that uses a subnet as a real de stination
C. dynamic source NAT that uses a range as a mapped source
D. static destination NAT that uses a subnet as a real source
【单选题】
Refer to the exhibit. 【nat(ins,any)dynamic interface】Which ty pe of NaT is configured on a Cisco ASA?___
A. dynamic NAT
B. source identity NAT
C. dynamic PAT
D. identity twice NAT
【单选题】
Which mitigation technology for web-based threats prevents the removal of confidential data from the network?___
A. CTA
B. DCA
C. AMP
D. DLP
【单选题】
Refer to the exhibit. What is the effect of the given configuration?___
A. It establishes the preshared key for the switch
B. It establishes the preshared key for the firewall.
C. It establishes the preshared key for the Cisco ISE appliance
D. It establishes the preshared key for the router.
【多选题】
What are two major considerations when choosing between a SPAN and a TAP when plementing IPS?___
A. the type of analysis the iS will perform
B. the amount of bandwidth available
C. whether RX and TX signals will use separate ports
D. the way in which media errors will be handled
E. the way in which dropped packets will be handled
【多选题】
What are two direct-to-tower methods for redirecting web traffic to Cisco Cloud Web Security?___
A. third-party proxies
B. Cisco Catalyst platforms
C. Cisco NAC Agent
D. hosted PAC files
E. CiSco ISE
【多选题】
Which three descriptions of RADIUS are true? ___
A. It uses TCP as its transport protocol.
B. Only the password is encrypted
C. It supports multiple transport protocols
D. It uses UDP as its transport protocol
E. It combines authentication and authorization
F. It separates authentication,authorization,and accounting
【多选题】
Which two configurations can prevent VLAN hopping attack from attackers at VLAN 10?___
A. using switchport trunk native vlan 10 command on trunk ports
B. enabling BPDU guard on all access ports
C. creating VLAN 99 and using switchport trunk native vlan 99 command on trunk ports
D. applying ACl between VLAN
E. using switchport mode access command on all host ports
F. using switchport nonegotiate command on dynamic desirable ports
【多选题】
What are two features of transparent firewall mode ___
A. It conceals the presence of the firewall from attackers
B. It allows some traffic that is blocked in routed mode
C. It enables the aSA to perform as a router.
D. It acts as a routed hop in the network.
E. It is configured by default
【多选题】
Which two models of A sa tend to be used in a data center?___
A. 5555X
B. 5585X
C. ASA service module
D. 5512X
E. 5540
F. 5520
【多选题】
Which two statements about hardware-based encrption are true?___
A. It is widely accessible
B. It is potentially easier to compromise than software-based encryption. It requires minimal configuration
C. It requires minimal configuration
D. It can be implemented without impacting performance
E. It is highly cost-effective
【多选题】
In which two modes can the Cisco We b Security appliance be de ployed?___
A. as a transparent proxy using the Secure Sockets Layer protocol
B. as a transparent proxy using the Web Cache Communication Protocol
C. explicit proxy mode
D. as a transparent proxy using the Hyper Text Transfer Protocol
E. explicit active mode
【单选题】
1.三相刀开关的图形符号与交流接触器的主触点符号是___。
A. 一样的
B. 可以互换
C. 有区别的
D. 没有区别
【单选题】
2.刀开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
3.行程开关的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
4.交流接触器的文字符号是___。
A. QS
B. SQ
C. SA
D. KM
【单选题】
5.熔断器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
6.热继电器的作用是___。
A. 短路保护
B. 过载保护
C. 失压保护
D. 零压保护
【单选题】
7.交流接触器的作用是可以___接通和断开负载。
A. 频繁地
B. 偶尔
C. 手动
D. 不需
【单选题】
8.三相异步电动机的启停控制线路由电源开关、熔断器、___、热继电器、按钮等组成。
A. 时间继电器
B. 速度继电器
C. 交流接触器
D. 漏电保护器
【单选题】
9.三相异步电动机的启停控制线路中需要有___、过载保护和失压保护功能。
A. 短路保护
B. 超速保护
C. 失磁保护
D. 零速保护
【单选题】
10维修电工以___、安装接线图和平面布置图最为重要。
A. 电气原理图
B. 电气设备图
C. 电气安装图
D. 电气组装图
【单选题】
11.熔断器的额定电压应___线路的工作电压。
A. 远大于
B. 不等于
C. 小于等于
D. 大于等于